matrix reloaded

[radiotech]

where can i order the matrix reloaded with the best price and support? thanks

[rolfw]

May not be the absolute cheapest price radiotech, but for support and service I would be inclined to point you at Toecutter's Den. That's where I got mine and unlike many other places, it comes fully loaded and ready to go, plus there is always someone here or there to help you through any teething problems.

[Channel Hopper]

If you need help in finding TCs den just look at the Irdeto section for a link. You will have to register first before accessing

By the way where in the US is Hell on Earth (or is it an alternative name for the place ?)

[radiotech]

Thanks Rowf and Channel hopper. i already registered with the Den. Heh heh, Hell on earth, USA is just for fun. I have not found any place on earth that is resemblant of Hell.

If you need help in finding TCs den just look at the Irdeto section for a link. You will have to register first before accessing

By the way where in the US is Hell on Earth (or is it an alternative name for the place ?)

[Norm]

Hi Rolf, have just decided to take the plunge and order an MR from Toecutter's. I see from having a look around Toecutter's that you have a BEC receiver - is that where you use the MR? I also have a BEC, the 6800CIP.

[rolfw]

Yes it is Norm, mine's the 6600ci though, it had problems with CAMs until I updated the software to the latest version.

I also used it to update the CAM with my CAS Interface and the new initialisation, so you should be OK.

[radiotech]

Rolfw, if you don't mind, please guide me to where i can download the latest software for the Bec-6600+ci. Thank you in advance. if you cannot post the link, please PM me.

[rolfw]

I have it here, it was sent to me by Chaintech in the far east, I'll see how big it is and see if I can upload it.

Can't upoad the PDF with the instructions, too big, will see if I can split the file.

OK, all done, normal warnings though.....use at own risk etc

I would also add that this is the European software, it may be different for the states.

[Norm]

Thanks for the encouraging response Rolf regarding the MR CAM. Do you know how I would be able to check what the latest version of software is for my BEC 6800? And where I could find it if required?

I'm sorry - I seem to have turned this thread around a bit! Norm.

[Norm]

A short update - I received my CAM yesterday and it works just fine in the BEC6800. Rolf, that was an absolutely excellent tip you passed on about buying it from Toecutter, thank you very much!

[rolfw]

No problem Norm, hope you get as much enjoyment from it as us other users.

Only problem with this hobby, is that the next purchase is always waiting around the corner.

[radiotech]

Rolfw, thank you for the Bec's files. I always received help from you whenever i ask for help.

[Razor]

Did Toecutter's give you a warranty with it. I ask because Astratec do not, and both have sort of close ties.

[Razor]

Sorry only if you use Cas-Interface, see below

In stock due to many requests !

Cas Interface for Magic, Axas, Universal, Matrix Cams

This Product can be used for Programming the cams
listed above .

We do not advise the use of this product as it can
easily damage your cam and the unit is also fragile .

No warranty , software or support is issued with
this product .

We will not cover warranty on Cams purchased
from us after using this product .

[rolfw]

I think what they are saying is that it is possible to do physical damage to the CAM with the CAS interface and to damage the contacts of the CAS itself, nobody is going to cover the CAM or interface against self inflicted damage.

Once you change the software on any of this type of equipment, you in effect void any warrantee, but as far as I know Toecutter's will always help if possible.

PS I don't believe that there are any close ties between Astratech and the Toecutter forum, but even if both offered the same service and price, I would always go to Toecutter's, as the money goes straight towards running the forum.

[Razor]

Yes, I also would choose Toe's over Astratec, and if he does offer better support anyone reading this thread might now lean his way. That is if they are in the market for some new gear. I do drop into the den once in a while and see that he is well respected and trusted.

[Strat92]

Hi. I'm in the Toronto Canada area and would like a Noth Americanm software update for BEC DB 6600+ CI. Thanx in advance.

[simo55]

full x2 freez with MR 1.100

[mike t]

hi im in canada is`any one have program for my BEC6800 FTA or update plese send me to miketriff88@hotmail.com

[rolfw]

Try E-mailing Jasonpeng @ chaintech.com.tw

Send details of your existing software and receiver model and serial number.

[george1960]

can somebody help please? i am looking for a user guide for bec db 6600 ci

[george1960]

can anyone help please i have recieved a bec reciever DB 6600 CI as a gift without user guide do you know where can i download that ?

[rolfw]

You may be able to download one from Chaintech as above, if not, send them an E-mail, they are very helpful.

[Norm]

I have a DB6600/DB6800 operation manual that I can photocopy at work if you're stuck. You can PM me your address. But be warned - it's not exactly a comprehensive document.

[george1960]

thanks rolfw
thanks norm
dear norm i cant access your e mail please e mail me that
my e mail lionheart_558@hotmail.com