Technomate TM-1500CI+ firmware update?

mpvdvoorde · 02-03-2006

Hi all,

I have a Technomate with firmware version 1.53... how can I update this and where can I find the software to do so. www.technomate.Com only has the 1.53 version.... You can post here or send by mail to
No e-mail addresses use the forum.
READ FORUM RULES, thank you.

Thanks.

Marc

Mick21367 · 02-03-2006

Head for the Links Section on this very forum and you will find plenty of links to other sites offering firmwares. Just a question of picking one you like the look of, there is only one alternative firmware to the official one, I think.

**rolfw** · 02-03-2006

Yep and also there is a sticky thread at the top of the receiver software section entitled "So you want receiver software patches"

mpvdvoorde · 03-03-2006

Checked the pages but none of them apply to my model, so any help still requested. Thanks.

**rolfw** · 03-03-2006

Look on the main forum for ***** http://67.18.198.220/forum/index.php there are patches there for the 1500s, you will have to register to download any files..

mpvdvoorde · 03-03-2006

Thanks guys, the altsat forum resolved the problem. Listen one more question regarding the receiver. I have 2 slots, one where you slide in your card and one that looks like a pcmcia. The pcmcia slot always gives me coded channel, however if I use that card in the upper slot it works fine...any solutions to that? Thanks in advance.

**rolfw** · 03-03-2006

The CI slot is for an additional CAM, so if you had two viewing cards, you could put a Nagravision/Conax/Mediaguard/irdeto CAM in there with a subscription card.

mpvdvoorde · 03-03-2006

I knew that was for an additional card and I do have two...but do you have to install the CI thing? Since both cards work in the normal slot but the CI doesn't seem to work... always says coded signal...

**rolfw** · 03-03-2006

The CI slot requires a CAM, do you have one in there?

mpvdvoorde · 03-03-2006

Yes I do, an official mediaguard CAM...and the weird thing is that if I remove the smartcard that's in there and just plug it in, then there is no problem, however if I put it in via the mediaguard cam it says that the channel is codeD...something weird... do you need to install it or something or change a code somewhere?

**rolfw** · 03-03-2006

Silly question, but have you tried the card both ways up?

emirim · 03-03-2006

If you use a CAM in TM1500CI, try to reset patching: go to menu-system information- and press 2004 with remote

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
new firmware 1.50 for technomate 1500ci today	sat200	Receiver software, international Section	13	22-06-2009 06:11 PM
How Can I Update My Reciver	excell	Viaccess	12	19-07-2008 07:20 AM
Free-xtv Update Sky Box Not Responding	ars1604	Receiver software, international Section	17	07-01-2005 09:19 AM
TECHNOMATE TM-5500CI on Astra 28.8E?	jAk	DISH SETUP: Single sat, Multi-Sat & Motorised systems	1	27-01-2004 04:42 PM
Update Windows today - before it gets Blasted	net1	Computer Discussion	13	22-08-2003 12:19 AM

Technomate TM-1500CI+ firmware update? Information exchange on digital satellite systems other than Sky

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)