MR on Strong 4375 (& Hispasat)

Godzuki · 17-01-2004

I've been lurking for a while now but can't seem to find the info I'm after.

My setup consists of:
Strong SRT-4375, MR CAM (1.055), Stab RotorSat 120HH motor,
60cm mesh dish (ex-$ky analogue) & Cambridge Platinum 0.6db LNB.

I am located near Liverpool (Longitude:2.8, Latitude:53.4).

I was hoping I could get some help with a few queries.

1) Does MR CAM (1.055) work on Strong 4375 without replacing IC (U206)?
2) With updated keys, what channels should I get from Hotbird/Astra 19.2?
3) Should I get a flicker of a signal at 30w on 60cm mesh dish & 0.6db LNB?

Any comments would be appreciated, TIA.

**Razor** · 17-01-2004

Originally Posted by Godzuki

I've been lurking for a while now but can't seem to find the info I'm after.

My setup consists of:
Strong SRT-4375, MR CAM (1.055), Stab RotorSat 120HH motor,
60cm mesh dish (ex-$ky analogue) & Cambridge Platinum 0.6db LNB.

I am located near Liverpool (Longitude:2.8, Latitude:53.4).

I was hoping I could get some help with a few queries.

1) Does MR CAM (1.055) work on Strong 4375 without replacing IC (U206)?
2) With updated keys, what channels should I get from Hotbird/Astra 19.2?
3) Should I get a flicker of a signal at 30w on 60cm mesh dish & 0.6db LNB?

Any comments would be appreciated, TIA.

Full list of MR channels here
http://www.satellites.co.uk/php-bin/...ead.php?t=8529

As for a signal from 30W with 60cm dish....Not sure but would say no.

Will MR work in your box....Ask them before you buy.

Also...Lurking is ok for a while, but after a while you just have to dive in.

Godzuki · 18-01-2004

Razor, Thanks for the pointers.

MR CAM doesn't seem to decrypt some(all?) of packages mentioned, I may have to replace that IC. Will take this issue over to MR forum.

I've had the 4375 for over 2 years and MR for 3 months, so "ask them before you buy" isn't a realistic option.

Guess I'll also be upgrading to a bigger dish then.

Cheers.

Godzuki · 02-02-2004

Just got my 4375 (with u206 replaced) back from local TV/Sat shop (cost £10).

Wow! I can decode channels again!

This hardware fix seems to work a treat, now I need to apply the software fix.

mike501 · 30-04-2004

where can you go to get your receiver upgraded to work with Magic Module?

mike501 · 04-05-2004

Did you get MR to work on your strong 4375?

Originally Posted by Godzuki

I've been lurking for a while now but can't seem to find the info I'm after.

My setup consists of:
Strong SRT-4375, MR CAM (1.055), Stab RotorSat 120HH motor,
60cm mesh dish (ex-$ky analogue) & Cambridge Platinum 0.6db LNB.

I am located near Liverpool (Longitude:2.8, Latitude:53.4).

I was hoping I could get some help with a few queries.

1) Does MR CAM (1.055) work on Strong 4375 without replacing IC (U206)?
2) With updated keys, what channels should I get from Hotbird/Astra 19.2?
3) Should I get a flicker of a signal at 30w on 60cm mesh dish & 0.6db LNB?

Any comments would be appreciated, TIA.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Strong 4375 upgrade	refinechange	Receiver software, international Section	5	30-01-2008 02:07 PM
Que canais ha em sinal aberto?	soprano53	Kaon	2	03-08-2006 06:03 AM
Novas frequencias no hispasat 23/05/2006	filtro	Instalações de Antenas & Frequências dos Sats	1	24-05-2006 07:49 PM
Hispasat lobbies for a Digital +'s contract	net1	Daily Satellite and Broadcast industry News	1	15-08-2004 07:12 PM
strong 4375 problems installing for analogue	ronn	DISH SETUP: Single sat, Multi-Sat & Motorised systems	5	02-02-2004 08:34 PM

MR on Strong 4375 (& Hispasat) Information exchange on LNBs, Single satellite, motorised and multi-satellite systems. DiSEqC switches, positioners, motors, actuators, dish-alignment etc.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)