Dreambox 500 - JTAG Information

bg4vhj · 27-04-2008

sorry to mhku!!

angusc · 27-04-2008

Originally Posted by mhku

Gemini 4.20

You need to keep the init file in /etc to reset your MAC address on each restart; the other methods discussed may be more permanent but I've not tested any of the MAC address methods.

Do i need to change the Attributes of the init file? I note on creation that it is 644 but the original init file is 755, i tried to change the attributes in properties but this still does not seem to work on reboot.....A B C guide for me? I did not understand the chinese reply, the english translation was not good.......Wo Ting Bu Dong...?

**mhku** · 27-04-2008

If you enable vcard in your profile other members can send you email - this may help if you need to speak not in English.

I haven't tested the init file/ MAC address solutions but it should be 755 permissions.

bg4vhj · 28-04-2008

Originally Posted by angusc

Do i need to change the Attributes of the init file? I note on creation that it is 644 but the original init file is 755, i tried to change the attributes in properties but this still does not seem to work on reboot.....A B C guide for me? I did not understand the chinese reply, the english translation was not good.......Wo Ting Bu Dong...?

Are you Chinese ?

angusc · 28-04-2008

Originally Posted by bg4vhj

Are you Chinese ?

No, I'm English living in China. Hense my Chinese is not very good.

angusc · 28-04-2008

Originally Posted by mhku

If you enable vcard in your profile other members can send you email - this may help if you need to speak not in English.

I haven't tested the init file/ MAC address solutions but it should be 775 permissions.

Yes i changed the attributes to 775 and now today it seems to work and the MAC address is changed on boot up.

Thanx for your help.

dj_713 · 30-04-2008

i do everything but i can't write the flash
i want to ask about pin 18 to 25 i must pout a wire form 18 to 25 pin you say here and second i didn't put power on dream 500 . must put and the power after i connect the parallel cable ?

check if you have this in your PC>

and need to make lot of try to connect...
in some board i try 2-3 times and some other 20-30times to connect.[/quote]

freon · 01-05-2008

On LPT connector you short connect pins 18 to 25, and there goes wire for ground.
when you click connect on program simultaniously put the power to box.

kornholio · 01-05-2008

Hi dj_713

take a look at the attached photos of this post.
It is my jtag cable.
They may help you.

Be carefull not to exceed the limit of 10 cm length!

garryh · 01-05-2008

when i tried to do mine could not get it to connect using windows so i used Jtag dm500 boot loader sif for dos this connected first time for me

Drash · 02-05-2008

Hi all
I have a problem
When i click write and comes to 5 or 7 % and then the programm closes or crashes
what seems to be the problem??
my wires are about 20 cm long. could it be the problem??
Tnx

Drash · 02-05-2008

It`s alive!!!!!!!!
I just cut the cable to 10cm and it worked

txn all

04-05-2008

Dear mates ,

This is a guide that we create after a successful recover of a dead dm500s . It contains photos and automated scripts .

Greetings from Greece .

Jyapgr - Jxid

Link:

_http://www.zshare.net/download/11517582c93539b5/

dj_713 · 04-05-2008

thanks very much

i am from greece and chania

with your jtag my dream 500 is now alive

thanks alot

work in dos mode but very good

Originally Posted by JYAPGR

Dear mates ,

This is a guide that we create after a successful recover of a dead dm500s . It contains photos and automated scripts .

Greetings from Greece .

Jyapgr - Jxid

Link:

_http://www.zshare.net/download/11517582c93539b5/

ssf01 · 06-05-2008

Thanks all,
I have Question. Is there any way to connect the cable to Dreambox500 without doing solder the cable to the dreambox500 board. I creat the cable with LPT connector but my question for the other end. Imagine I have 100 of dreambox, It will take alot of time to connect them.

Any answer please?

Thanks

retrospec · 06-05-2008

Thank you very much for the usefull information in this thread.

Just made a jtag cable as described connected at first time and uploaded the boot image found linked in this thread, all seems ok.

FYI. I did not know that i had a clone, checked all the information from dream multimedia to detect it and seemed genuine. Howerver i noticed one little difference after it died. there is a yellow chip onboard the mcb that is black on the original, thats the only difference i have found.

06-05-2008

Originally Posted by ssf01

Thanks all,
I have Question. Is there any way to connect the cable to Dreambox500 without doing solder the cable to the dreambox500 board. I creat the cable with LPT connector but my question for the other end. Imagine I have 100 of dreambox, It will take alot of time to connect them.

Any answer please?

Thanks

Hello ,

The only that came up about is to create a jtag with a flat cable connector at the other end ( from a old pc or electronics parts store ) .

Then add the jumper pins into connector holes where they are needed. Now you have to attach it on pcb . You need only a trick to hold the connector stable . A metal plate or clip you will find out .

I hope that helps .

John

06-05-2008

Originally Posted by retrospec

Thank you very much for the usefull information in this thread.

Just made a jtag cable as described connected at first time and uploaded the boot image found linked in this thread, all seems ok.

FYI. I did not know that i had a clone, checked all the information from dream multimedia to detect it and seemed genuine. Howerver i noticed one little difference after it died. there is a yellow chip onboard the mcb that is black on the original, thats the only difference i have found.

Hello ,
Concerning the time bomb , it trace the hardware via MAC address .
Even if you have an original box with modified MAC , your DMbox is killed
too .

The reason that we create this friendly ( i hope ) guide is to reverse back
this action which destroy our dmboxes no matter what , in purpose .

Target reached i believe !!!

Regards

John

camoufle · 07-05-2008

a big thanks

bro · 19-05-2008

Originally Posted by freon

On LPT connector you short connect pins 18 to 25, and there goes wire for ground.
when you click connect on program simultaniously put the power to box.

so you connect 18 and 25 of 18 to 25,,i have seen tutorials where they are all connected but the picture in the post above has just the two connected,i am c
confused

20-05-2008

Originally Posted by bro

so you connect 18 and 25 of 18 to 25,,i have seen tutorials where they are all connected but the picture in the post above has just the two connected,i am c
confused

Hello ,

You have to short all the pins together in a row . <18-19-20-21-22-23-24-25> this is the ground and just one cable
from those soldered pins goes to DM500s 16 pin .
Follow my guide above step by step .Your clone DM500s will be
fixed after then.

John

bro · 20-05-2008

thanks john,will try that,what also confused me that in some guides theres a resistor and wire connected to pin 13 instead of 11

11 --> 100 ohms --> 1 ( Tdo )

bro · 20-05-2008

thanks mate i now have the dreambox back up and running
i also used the aio files you posted

tester0001 · 01-06-2008

I successfully connected and brought my DM500 back to life following all the steps highlighted in the forum using one of the blimg file with a good MAC address. I now have power and the boox turn on fine. Thank you all.

I still have one problem I can't resolve however, and that is the fact that I can't connect via the netwrok to the box. My Control Center software fails to see the box on the network or connect to the box although the LAN light is green on my router. Is there a fix for this? if someone can point me to where the steps are to correct this it would very appreciated.

tester0001 · 01-06-2008

Any one able to help on the LAN connection for my dreambox above?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Dreambox 500 - JTAG Information Dreambox500 - Support for the Dreambox 500 DM-500 satellite receiver.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)