Downgrading TIT From 1.06 To 1.03??

**inabsentia** · 01-02-2005

Sorry, I put this on another part of the board before realising it would be better suited on here.

Got a Blue Tit that's given a couple of years good service-I've now got a situation where I need to downgrade the OS from the current 1.06 to 1.03.

I've done this before using TITCARDPROG 1.10, but this time, although the progger goes through the routine, it comes out 1.06 at the end. Also tried Titanium Updater 1.0 and that just tells me it is up to date (OS1.06).

Anyone point me in the right direction of something that will work? I'm using an Infinity USB Phoenix progger.

***psats*** · 01-02-2005

try this one it work fine for me..

**inabsentia** · 01-02-2005

Than ks for that mate, still no joy here-it runs through the procedure, then comes up 'Failure to write card'

Tiggy · 07-02-2005

Thanks for the file/program.
Worked wonders on Tit and aston1.05.
Needed to use D+ AND DOWNGRADE TO 1.03 O/S TIT and you came up trumps.

Have gone from 1.06 >1.03 >1.06 without trouble.

Using Multipro, check that the multiprog program is running and on pheonix 3.58 megs.

I had trouble trapping the card recently and the program was not set to run on the pheonix set up.
Tiggy

***wolfav*** · 07-02-2005

inabsentia have you tried down grading the os one at a time

**saturnorbit** · 07-02-2005

Originally Posted by wolfav

inabsentia have you tried down grading the os one at a time

Wolf-- do u know any software that will do that?

just load these files, and u will have os 1.03

buckhouse · 12-02-2005

Thank you Saturnorbit for your help; successfully downgraded Titanium from OS 1.06 to OS 1.03.

Used USB Phoenix Programmer set at 3.58 not normal 3.68, saw this somewhere would probably be OK with 3.68.

Run Titanium Loader version 1.2 and erased files

Run Titanium Loader version 1.2 using Flash & Eprom from “Titanium Restore OS 1.03” file

False ATR(something like 3B) is obtained

Run TitaniumCardprogger1[1].10.02.Received unsupported titaniumsoftware/No ATR messages. Disregard this, you might have to disregard several times by pressing 'connect programmer' & 'reset' buttons alternately, eventually the ATR now shows OS 1.03.

S*CA2 working on M.R. with 1.170 Software in Echostar AD3000- IPVA

mayous · 27-04-2005

Originally Posted by buckhouse

Thank you Saturnorbit for your help; successfully downgraded Titanium from OS 1.06 to OS 1.03.

Used USB Phoenix Programmer set at 3.58 not normal 3.68, saw this somewhere would probably be OK with 3.68.

Run Titanium Loader version 1.2 and erased files

Run Titanium Loader version 1.2 using Flash & Eprom from “Titanium Restore OS 1.03” file

False ATR(something like 3B) is obtained

Run TitaniumCardprogger1[1].10.02.Received unsupported titaniumsoftware/No ATR messages. Disregard this, you might have to disregard several times by pressing 'connect programmer' & 'reset' buttons alternately, eventually the ATR now shows OS 1.03.

S*CA2 working on M.R. with 1.170 Software in Echostar AD3000- IPVA

hi, my atr is bloked on 3B i attempt to press several time connect and reset but the answer is no atr. could you help me?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Downgrading TIT From 1.06 To 1.03??	inabsentia	Cards & Programmers General	0	01-02-2005 11:35 AM
Multi-Yo! programmer +Tit card how to?!!	hellpic	Conax, Cryptoworks, Nagravision, NDS and Others	4	26-09-2004 01:21 AM
OS 1.03 or 1.06 - confused newbie!	markhunter99	Cards & Programmers General	1	20-08-2004 12:24 PM
C*nax, MR and Tit card: works on/off	erik1	Cards & Programmers General	7	25-04-2004 10:09 PM
For all the new guys that need help programming tit	dont get it	Matrix Reloaded, Revolutions and CAS interface	8	08-03-2004 02:55 PM

Downgrading TIT From 1.06 To 1.03?? Discussion on the new breed of satellite TV "Super Cards"

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)