Advice Needed Best drill bit for metal

Captain Jack

Burnt out human
Joined
Oct 21, 2006
Messages
11,797
Reaction score
7,980
Points
113
My Satellite Setup
See signature
My Location
North Somerset
Hi,

Could someone suggest me the best drill bit to buy for drilling into metal? I keep buying "titanium" Bosch ones from B&Q as a set but after a few drills, they become blunt and unusable.

I don't mind spending a bit more on something that will last - generally use size 8 and 10 but a good set will be fine too.

Alternatively, does something exist to sharpen existing bits - and actually works?

Thanks
CJ
 

Archived-1

Persona non grata
Joined
Apr 14, 2007
Messages
7,570
Reaction score
8,590
Points
113
My Location
uk
When I used to work with steel, I used to sharpen my own check the link CJ, also when drilling use a very low speed and it helps to use a little oil, as for a good bit now days I have know idea, I work with wood mainly now.
 

hairybadger

Bricoleur
Joined
Jul 20, 2012
Messages
1,377
Reaction score
778
Points
113
Location
46.1N 6.4E
My Satellite Setup
see sig
My Location
near Geneva, Haute-Savoie, France
When I used to work with steel, I used to sharpen my own check the link CJ, also when drilling use a very low speed and it helps to use a little oil, as for a good bit now days I have know idea, I work with wood mainly now.
There is a (notional) ideal speed for each metal and bit diameter. You can look up "drill speed calculator" or something like that.
 

PaulR

Dazed and Confused Admin
Staff member
Joined
Jun 28, 2003
Messages
18,023
Reaction score
4,046
Points
113
My Satellite Setup
-----------See sig-----------
My Location
Wirral, NW UK and Vaucluse, France.
Rather than buy sets why not buy individual ones? I buy mine at Tool Station. They're cheaper than Screwfix but there are less of them around. You may have to go to Screwfix (who are, incidentally, owned by the same company that owns B&Q).

But why are they wearing out so much? What are you drilling?
 

Captain Jack

Burnt out human
Joined
Oct 21, 2006
Messages
11,797
Reaction score
7,980
Points
113
My Satellite Setup
See signature
My Location
North Somerset
But why are they wearing out so much? What are you drilling?

Just through metal - steel between 2 and 5mm thick. Maybe I am doing it wrong - too fast and certainly no oil.
 

hairybadger

Bricoleur
Joined
Jul 20, 2012
Messages
1,377
Reaction score
778
Points
113
Location
46.1N 6.4E
My Satellite Setup
see sig
My Location
near Geneva, Haute-Savoie, France
Just through metal - steel between 2 and 5mm thick. Maybe I am doing it wrong - too fast and certainly no oil.
hmmm didn't know about the oil :) will bear it in mind next time....
 

Channel Hopper

Suffering fools, so you don't have to.
Staff member
Joined
Jan 1, 2000
Messages
35,533
Reaction score
8,554
Points
113
Age
59
Website
www.sat-elite.uk
My Satellite Setup
A little less analogue, and a lot more crap.
My Location
UK
Oil is less efficient than water in carrying away the heat from the centre of the bit. In lathe work the lubricant is a water soluble oil to offer clean cutting, cooling and fast debris removal
 

sonic1

Specialist Contributor
Joined
Aug 6, 2004
Messages
870
Reaction score
114
Points
43
Age
49
My Satellite Setup
Vu + Ultimo 4K - Solo 4K - Uno 4K - Duo2- SoloSE - Zero- Uno -Prismcube Open Black Hole - 0.6 , 98cm Funkee , 28E-23.5E-19E-13E
My Location
Black Hole Team
Always used oil and a slow drill, common sense says pressing hard in to metal with a fast drill will create heat and melt the end of the drill.
Easily sharpened as shown in post 2 and a decent bit will last ages is looked after.
 

purplemarina

Specialist Contributor
Joined
Jul 26, 2009
Messages
604
Reaction score
324
Points
63
My Satellite Setup
2x 1.2m motorised channelmasters . tm 5302, tm6902,
My Location
hampshire uk.
I use dormer drills very good quality and seem to last forever, they can be quiet expensive but ive had some bargains off eb*y.
 

Piltdownpaul

No.1 Spike Milligan Fan
Joined
May 27, 2012
Messages
2,011
Reaction score
687
Points
113
Age
55
My Satellite Setup
Skybox F3,Icecrypt S3500HDCCI, Technomate TM3000D,TM5400Ci Super, Samsung HD HDD Freesat Box,60cm dish for freesat, TD88 dish on a Skybox F3 57E to 45W.
My Location
South Leicestershire (Fleckney)
Reducing the drill speed should help,are the drill bit ends "blueing" after drilling, if so there's too much heat about too.
 

Terryl

Specialist Contributor
Joined
Apr 14, 2011
Messages
3,246
Reaction score
1,932
Points
113
Age
82
My Satellite Setup
OpenBox X5 on a 1 meter motorized dish.
And now a 10 foot "C" band dish.

Custom built PC
My Location
Deep in the Boonies in the central Sierra Nevada mountains of California.
This all depends on the type of steel being drilled, how thick, how hard, how big of a hole.

For thick steel a slow speed mounted in a drill press with a water base lube should be used, a big hole should be drilled in several steps, the harder the steel the harder the drill bit needs to be, some steels need a different bit then others.

Look here for some good choices, http://www.mcmaster.com/#standard-drill-bits/=qmyw20
 

Vipersan

Emmett Browns Ghost
Joined
Jun 29, 2009
Messages
10,918
Reaction score
6,663
Points
113
Age
66
My Satellite Setup
IP9000HD +
TD110 Dish and TD88 Dish in Tandem
66°East to 60°West.
AZbox PrmHD + OpnbxS9HD + Skybox + DrHD F15
2x VboxII AZ-EL
2 m+ Alcoa PF + BSC421 C-Band lnbf...
+SS2/TwHnS2-3200 pci/TBS6925 pci
1.5 Fortec Star -Gbox - HtoH Ku/Ka/C
My Location
UK
Wherever possible ..
I use a lower speed in a stand/press drill ..
& Individually purchased drill bits..rather than those cheap kits..
And a high speed twist drill if I have to work with a hand drill.
Always start with a smaller pilot and work up size in 2mm steps until desired size achieved.
No specific brand comes to mind but Dormer are good.
My latest addition is a step drill (obviously plate only to depth of about 6mm)..which is superb for copper/Alluminium ..even mild steel if it's not too thick..
rgds
VS
 
Top