desperately need help!!

[shazmart]

Hi guys, still trying to programme my blue titanium card (using my infinity usb & the titanium card progger which i downloaded) but i keep getting the message:
"ATR : NO ATR! unsupported titanium os found". I`ve spent the last three nights searching forums and downloading files/programmers/testers etc...but i can`t seem to get anywhere. I may even have permenantly damaged the card somehow!! As i`m still in the early learning stage at all this, can anyone advise me what i`m doing wrong? is there something so simple that i`m not doing? any help/advise would be much appreciated.

 

[Razor]

Have you loaded the software that came with the programmer. If so double click on the infinity usb icon. It be set to wafercard as default at the right of this box there is another grey box, it says PHOENIX. Click on this and a box will pop up. It should have a list of frequencys, put a dot at 3.58mhz and click ENABLE. It will then minamize to your task bar. Do all this while your card is in the slot with the chip downwards.

Come back to me when this is done.

 

[shazmart]

thanks for taking the time to help me razor...firstly when i open the usb icon, each time i get the same message "no cpu could be detected on the inserted card, clean the contacts & make sure the contacts are facing downwards" the i click `ok`...fine. next to the wafer card window is the infinity logo ("alias: singlepic"). when i click on it, a `detect` window opens up :cpu (avr/pic) & memory (external eeprom) then if i click "detect" the progress bar runs all the way then...nothing else happens.

 

[Razor]

Never click on detect.

Just do the steps above, then open Tit programer v1 [1].10.0 if you have it.

What programmers have you...and what CNX file have you.

 

[shazmart]

it`s a titanium progger v1.10.2 which i downloaded. my programmer is an Infinity usb (just a usb - no external adaptor) and cnx (conax?) file??? i don`t know what this is...sorry. maybe that`s what i`m doing wrong. There`s no list of frequencys in my usb programmer.

 

[Razor]

I see where the fault is....You have a Infinity USB Programmer, when tit cards came out they brought out an Infinity USB PHOENIX Programmer as this is the only type that will program a tit card. They look the same and cost about the same but are really different beasts altogether.

Tit can only be loaded in PHOENIX mode.......Sorry.

 

[shazmart]

wow...when i`ve erased the card,all seems well untill i try and go any further. In your expert oppinion, do you think i`ve actually erased the card or worse still, screwed it up completely?

 

[Razor]

NO...It should be OK.

 

[shazmart]

Many thanks Razor...now at least i can get some rest, i won`t be wasting any more time trying to do the impossible. I will be back...Cheers.

 

[shazmart]

Hi all, just got a phoenix programmer and i`m now getting somewhere but i have one small (i hope) problem. When i click the `load .hex - load .eep`buttons, Great..but i don`t know what to do with the `load cr.key` button. I`m using the TMB files but there are only two...should there be three? any advice guys? many thanks.

 

[coconut]

just forget the cr.eky if it come without it.

 

[john_graydon]

Hi all, just got a phoenix programmer and i`m now getting somewhere but i have one small (i hope) problem. When i click the `load .hex - load .eep`buttons, Great..but i don`t know what to do with the `load cr.key` button. I`m using the TMB files but there are only two...should there be three? any advice guys? many thanks.

Did you get it sorted.

 

[Razor]

Dont do anything with the `load cr.key` , Just load Hex and EEP

 

[shazmart]

Ok! done that ...how can i tell if i`ve done it correctly ( what should i be able to watch?)

 

[Razor]

What file did you load.

 

[shazmart]

TMB.hex and TMB Eep.

 

[Razor]

Go down to the chat room near the end of the main page, it will make things quicker