Dish tv in qatar

Status
Not open for further replies.
S

shabin

Member
Messages
4
My Satellite Setup
NSS6
Desktop
My Location
Qatar
Hi,

Im using dishtv zenega hd reciever in qatar. majority of my transponders have a signal quality of 80% and above and even 94%. But, 5 transponders especially for channels, Kairali TV, Amrita TV, Jeevan TV, Jaihind TV etc. i use a 160 cm dish with a 4 port lnb eurostar. The 4 port was suggested by my technician as the snr will be higher. all the other channels are perfect except at times.

please advice what should be done next.:confused
 
A

ahamed12

Member
Messages
1
My Satellite Setup
nss6, intelsat, abs1
My Location
Sri Lnaka
Please let know what which trasponders u r getting now
 
S

shabin

Member
Messages
4
My Satellite Setup
NSS6
Desktop
My Location
Qatar
5 transponders are not available...i need to check it.
 
S

shabin

Member
Messages
4
My Satellite Setup
NSS6
Desktop
My Location
Qatar
5 transponders have no signal: say 1-2% strength

10990 MHz 27500(V)
11070 MHz 27500(V)
11150 MHz 27500(V)
11570 MHz 27500(V)
11490 MHz 27500(V)


7 transponders are okay:

12688 27500 v Signal Strength= 76%; Signal Quality = 88%
12595 40700 v 78%;90%
12534 40700 v 78%;90%
11172 27500 h 85%;96%
11038 40700 h 84%;96%
12595 40700 h 78%;90%
12647 27500 h 78%;90%
 
Moradabad

Moradabad

SAT SPECIALIST INDIA
Messages
796
My Satellite Setup
One 12 Feet Heavy Antenna, one 10 Feet Double Rib Antenna

Dreambox Dm500S, DM 7025. HD Receiver,Envision,
Eurostar receiver, 4 Dual LNBS, 5 PFA Lnbs
My Location
india
shabin said:
5 transponders have no signal: say 1-2% strength

10990 MHz 27500(V)
11070 MHz 27500(V)
11150 MHz 27500(V)
11570 MHz 27500(V)
11490 MHz 27500(V)


7 transponders are okay:

12688 27500 v Signal Strength= 76%; Signal Quality = 88%
12595 40700 v 78%;90%
12534 40700 v 78%;90%
11172 27500 h 85%;96%
11038 40700 h 84%;96%
12595 40700 h 78%;90%
12647 27500 h 78%;90%
are you using prime focus dish or offset one
 
O

odiyan

OdiYaN
Messages
11
My Satellite Setup
ZENEGA DISHTV
My Location
ME
try this link

http://www.satellites.co.uk/forums/indian-subcontinent-general-section/81190-dish-tv-zenega-cd-1004-satellite-receiver-software-4.html#post564977

odiyan said:
Hi guys,
I figured to find a solution for the two frequencies in Zenega,

1) Get a splitter open it from the back side remove all connection from it.
2) get a insulated copper wire of medium guage, ( telephone or Network cable wire ok)
3) make ten turns on a pencil or a reynold ball point pen
4) solder the two ends to the spliter outputs (leave the input free)
5) make a small gap after the fifth winding. connect one end to lnb and other to the receiver
6) now you got to STB info and select red button for setup,
7) select hometransponder and adjust the winding gap till you get a quality of above 60%.

Its works in abudhabi UAE, fully tested, you need some patience in adjusting, and use a good LNB, noting like global, universal etc, use philips if you get it.

OdiYaN
 
Status
Not open for further replies.
Top