Dr Hd D15

hvdh

hvdh

Specialist Contributor
Messages
2,056
My Satellite Setup
Dr.HD F16, TBS 5927, T-55, Laminas 120 cm
My Location
Oss, NL (5.5°E 51.8°N)
Unfortunately this file doesn't allow for any orbital degree changes.
Of course you can. Clarke Tech Editor Studio leaves nothing to be desired!
And everything can be sorted or (bulk)edited.
Clipboard01.png Clipboard02.png
 
Costactc

Costactc

Specialist Contributor
Messages
811
My Satellite Setup
3m channel master mesh-24" vonweise actuator-ps1 x2 lnbf(L)-pansat ap3500 positioner-x2 premium III-vu+solo2.
2.4m fortec solid-24" vonweise actuator-esx 241 lnbf(c)-vbox 7 positioner- dm800.
1.2m fortec-24"sj actuator-invacom snh-031--tm 5402 m3.
My Location
Canada
I'm not too familiar with these editors, I didn't realise that I had to do the changes before flashing the receiver. I'll keep at it.
 
timo_w2s

timo_w2s

Retired Mod
Messages
4,359
My Satellite Setup
See Signature
My Location
Maidenhead, UK & Helsinki, Finland
I'm not too familiar with these editors, I didn't realise that I had to do the changes before flashing the receiver. I'll keep at it.
Basically you just need to make a copy of your channel list on to a USB stick (probably in a receiver's menu called USB or something) and then copy it on to the PC, make another copy of the file as a backup, load one of the files in the editor, make changes, save it, copy it back onto the USB stick and then upload it back onto the receiver.

I can't be too specific as I don't have a D15 with the newer firmware on it (I'm still using an F15 with the older SD firmware).
 
Costactc

Costactc

Specialist Contributor
Messages
811
My Satellite Setup
3m channel master mesh-24" vonweise actuator-ps1 x2 lnbf(L)-pansat ap3500 positioner-x2 premium III-vu+solo2.
2.4m fortec solid-24" vonweise actuator-esx 241 lnbf(c)-vbox 7 positioner- dm800.
1.2m fortec-24"sj actuator-invacom snh-031--tm 5402 m3.
My Location
Canada
I can't get the file from the stb into the editor and every time I attempt to create my own list, even after changing the properties, it always defaults to East and cannot get it to show me West.
 
hvdh

hvdh

Specialist Contributor
Messages
2,056
My Satellite Setup
Dr.HD F16, TBS 5927, T-55, Laminas 120 cm
My Location
Oss, NL (5.5°E 51.8°N)
Like timo_w2s said, in the receiver menu the should be something like utils - Upload NDF.
A .ndf or .cndf will be written to your USB stick.
Then insert the USB stick in your PC and open that .ndf or .cndf with Clarke Tech Editor Studio (CTES).
You can modify or add satellites and transponders to your liking.
In CTES, West is entered in the 360° East system, so for example 90.0° West is entered as 270.0° East.
Save the .ndf again (under another name to avoid confusion).
Insert USB stick into receiver, select Download menu, and select that ndf.
(I must have done this a thousand times on the Dr.HD F16 !)
 
B

bonou2

Member
Messages
110
My Satellite Setup
strong 4500, openbox X801, vantage 7100ts, vantage X201 CI, goldenmedia 9080,goldenmedia uni-box2,tbs6925+,inverto black ultra+C120,panorama er-861, zinwell lnb 15K C- band,intersat 20K
My Location
Romania
here are the list with 64 satellite position from 45W-90E, but only in KU-band
 

Attachments

Costactc

Costactc

Specialist Contributor
Messages
811
My Satellite Setup
3m channel master mesh-24" vonweise actuator-ps1 x2 lnbf(L)-pansat ap3500 positioner-x2 premium III-vu+solo2.
2.4m fortec solid-24" vonweise actuator-esx 241 lnbf(c)-vbox 7 positioner- dm800.
1.2m fortec-24"sj actuator-invacom snh-031--tm 5402 m3.
My Location
Canada
Ok. I just created my own satellite list from 8-125w by putting the orbital degree before the actual sat name and used East which was quite simple. Once the wifey wakes up I will flash my new sat file and hope for the best.
 
Costactc

Costactc

Specialist Contributor
Messages
811
My Satellite Setup
3m channel master mesh-24" vonweise actuator-ps1 x2 lnbf(L)-pansat ap3500 positioner-x2 premium III-vu+solo2.
2.4m fortec solid-24" vonweise actuator-esx 241 lnbf(c)-vbox 7 positioner- dm800.
1.2m fortec-24"sj actuator-invacom snh-031--tm 5402 m3.
My Location
Canada
Of course I had all the orbital degrees wrong....I finally managed to input all my sat positions from 8-125w. Thanks for the help folks, much appreciated. Scanning all ku sats with my 1.2m motorised dish.
 
william-1

william-1

Super Moderator
Staff member
Messages
9,463
Location
Epping Forest
My Satellite Setup
OP Gibertini 100 XP+ Inverto Black Ultra 0.2
Superior Dark Motor (160° max)
(50 east to 34.5 west)
TM6902HD (A/B switch) Octagon SX88+Optima

Raven 88cm Mesh Dish + TM-1 0.1
Stab100 H to H (120° max)
(53 east to 45 west)
Octagon SX88+ (A/B switch) Edision S2

45cm dish V8 Golden 28E FreeSat Quad Lnb
Virgin Media FreeSat
My Location
Epping Forest Essex
I can't get the file from the stb into the editor and every time I attempt to create my own list, even after changing the properties, it always defaults to East and cannot get it to show me West.
That is easily solved just load your channel list onto the TM editor & this editor will allow default to West satellites 1st.
 
S

Serafeim

Member
Messages
68
My Satellite Setup
5 dishes, Technomate 5402 M3
My Location
Arta, GREECE
I received my new d15 today. I loaded latest 135p but i cannot enter the biss menu pressing 8280. Is there any code that activates the emu?
 
digi247

digi247

In the Green Room
Messages
722
Location
NW
My Satellite Setup
see sig
My Location
UK
Red Button to access the Biss menu Green Button for the other Secret menu
 
Laser

Laser

Member
Messages
486
My Satellite Setup
Dr HD F15, OS mio + 4K, Octagon SF8008, Octagon SX88+. TM 5402HD M3. .Channel Master 1.20 Ku and C Band. 1.1 Triax Dish
My Location
Berkshire
Hello. Does anyone have the latest patch for the D15 that can be recommended.
Not sure which is best?
Thank you in advance
 
Laser

Laser

Member
Messages
486
My Satellite Setup
Dr HD F15, OS mio + 4K, Octagon SF8008, Octagon SX88+. TM 5402HD M3. .Channel Master 1.20 Ku and C Band. 1.1 Triax Dish
My Location
Berkshire
Thank you. Is the latest the best? I think I read 134P was the one to use?
 
Top