Log in
Register
Menu
Log in
Register
Home
What's new
Latest activity
Authors
Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Current visitors
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Satellite TV receivers & systems support forums
DISH SETUP: Single sat, Multi-Sat & Motorised
Humax IR-ACE-SII
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Bassa" data-source="post: 349789" data-attributes="member: 249964"><p>Hello All,</p><p>Hope someone can explain the following to me. <img src="data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7" class="smilie smilie--sprite smilie--sprite14" alt=":-doh" title="DOH! :-doh" loading="lazy" data-shortname=":-doh" />2 </p><p></p><p>I recently received a Humax IR-ACE-SII receiver along with a 105cm oval dish and Ku band LNB. This setup was used in Bahrain to view Pay channels, namley e-Pehla and e-Firstnet. The Transponder used was NileSat. The irdetto access card was in the slot. All these equipment were supplied by the service provider in Bahrain and also installed by them.</p><p></p><p>I live in Sri Lanka. Almost near colombo. So I set up the dish and LNB, and plugged it to the Humax and tried to lock on to Intelsat 12 (PAS 12).. no luck</p><p>Then on to NSS 6...again no luck. What I did was in the Installation menu, under Antenna Setting, I filled 2 user defined satellites.. I moved the dish all around.. but 0% signal strength and 0% quality. I used the calculator at <a href="http://www.satsig.net" target="_blank">www.satsig.net</a> to get the proper azimuth and elevation angles for both transponders.</p><p></p><p>Then i selected a preset Satellite transponder... there were several.. for e.g TURKSAT... and the signal strength burst to 89%.. Quality 0%.</p><p></p><p>This was the same for most of the other preset tranponders, with few exceptions.</p><p></p><p>I also tried with several different settings Such as choosing different LNB frequencies, LNB Power on/off.. but nothing.</p><p></p><p>I even tried Choosing Nilesat and then adjusting the dish for PAS 12. The signal strength went upto 91% but quality remained at 0%.</p><p></p><p>I later noticed that the receiver too was branded with the provider's logo.</p><p></p><p>I even bought a new LNB, thinking the old one was faulty.</p><p></p><p>Same results from the new one.</p><p></p><p>Pls can someone explain this situation. Any help appreciated!</p><p>Is it possible that the soft on the Humax is programmed in some way not to work without OTA updates? or some similar method?</p><p></p><p>Again any help to shed light on this situ is appreciated.</p><p>:-worship</p></blockquote><p></p>
[QUOTE="Bassa, post: 349789, member: 249964"] Hello All, Hope someone can explain the following to me. :-DOH2 I recently received a Humax IR-ACE-SII receiver along with a 105cm oval dish and Ku band LNB. This setup was used in Bahrain to view Pay channels, namley e-Pehla and e-Firstnet. The Transponder used was NileSat. The irdetto access card was in the slot. All these equipment were supplied by the service provider in Bahrain and also installed by them. I live in Sri Lanka. Almost near colombo. So I set up the dish and LNB, and plugged it to the Humax and tried to lock on to Intelsat 12 (PAS 12).. no luck Then on to NSS 6...again no luck. What I did was in the Installation menu, under Antenna Setting, I filled 2 user defined satellites.. I moved the dish all around.. but 0% signal strength and 0% quality. I used the calculator at [url]www.satsig.net[/url] to get the proper azimuth and elevation angles for both transponders. Then i selected a preset Satellite transponder... there were several.. for e.g TURKSAT... and the signal strength burst to 89%.. Quality 0%. This was the same for most of the other preset tranponders, with few exceptions. I also tried with several different settings Such as choosing different LNB frequencies, LNB Power on/off.. but nothing. I even tried Choosing Nilesat and then adjusting the dish for PAS 12. The signal strength went upto 91% but quality remained at 0%. I later noticed that the receiver too was branded with the provider's logo. I even bought a new LNB, thinking the old one was faulty. Same results from the new one. Pls can someone explain this situation. Any help appreciated! Is it possible that the soft on the Humax is programmed in some way not to work without OTA updates? or some similar method? Again any help to shed light on this situ is appreciated. :-worship [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Satellite TV receivers & systems support forums
DISH SETUP: Single sat, Multi-Sat & Motorised
Humax IR-ACE-SII
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top