Magic module with Conax official card

per73

Member
Joined
Mar 30, 2004
Messages
2
Reaction score
0
Points
0
Age
50
I am using a Magic Module ver. 1.04 that I have programmed with penta 1.11.
I would like to use it with an original Conax "Canal Digital Sweden" card.
The reason is that I don't have embedded Conax in the reciever "Humax VACI 5350".
The problem is that it seems to work fine for about eight seconds then the picture freezes, become black and a message that the video signal is coded appears, after eight seconds it's back to normal and working for about eight seconds again and so on. I have tried the card in a Conax CAM and then it's working.

Isn't the reciever supported by the MM?
I have read about fake MM ver 1.04, could that be the problem? How do I know if it's fake or not?
Is there different types of the software penta 1.11?
Isn't the software "penta 1.11" supporting original cards????????

I'm a newbie with this so I would be most thankfull if anyone could tell me what i'm doing wrong.
 

rolfw

Believe it when I see it Admin.
Staff member
Joined
May 1, 1999
Messages
38,292
Reaction score
1,615
Points
113
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
May be wrong, but I thought that Penta 1.11 emulates Conax, in which case there is probably a conflict between the CAM Emulator and the card.

You may have more luck with an earlier version penta.
 

S.G

Member
Joined
Mar 21, 2004
Messages
5
Reaction score
0
Points
0
Age
42
i have the same promblem but when i put a original conax card for canal digital it does even read the card.

I have a samsung dsr 9000 via ci..
i dont think my magic module is fake beacause i have bought it from a reiable source. i have a titanium card also and it doesnt work with conax but it works with seca2.
i have also a 6-1 funcard and it works perfactly but i dont know what the promblem is why dosent it work for conax.
i have programmed my magic module with penta 1.11 conax and it dosent work.

i want conax to work.
 

netjunkie

Member
Joined
Jul 31, 2004
Messages
30
Reaction score
0
Points
0
S.G said:
i have the same promblem but when i put a original conax card for canal digital it does even read the card.

I have a samsung dsr 9000 via ci..
i dont think my magic module is fake beacause i have bought it from a reiable source. i have a titanium card also and it doesnt work with conax but it works with S*ca2.
i have also a 6-1 funcard and it works perfactly but i dont know what the promblem is why dosent it work for conax.
i have programmed my magic module with penta 1.11 conax and it dosent work.

i want conax to work.
hi ya,
i have the same sammy9000 but can't get any of my working Aston1.5+tit or MRev cam to work on it. In settings they show up but just show black screens or complain saying "please check the smart card". do i need to install some new firmware? do you know what you use? please help me out if you can,
thanks,
netjunkie
 

network75

Regular Member
Joined
Jan 30, 2004
Messages
65
Reaction score
0
Points
0
Age
63
netjunkie said:
hi ya,
i have the same sammy9000 but can't get any of my working Aston1.5+tit or MRev cam to work on it. In settings they show up but just show black screens or complain saying "please check the smart card". do i need to install some new firmware? do you know what you use? please help me out if you can,
thanks,
netjunkie
Penta 1.11 does emmulate conax so Rolf does have a point - there may be a conflict.

The reason your tit card freezes after a few seconds is probably because you are using 1.06 OS on the card. I had that problem and changed to an older version and it worked. I later changed my receiver to a Technomate and I was able to use 1.06.

The best solution for all of this would be an upgraded Penta that would cope with the latest codes but there hasn't been one for a few months now.

Good luck, Tommo.
 

raja1

Member
Joined
Jun 22, 2006
Messages
3
Reaction score
0
Points
0
Age
40
My Satellite Setup
2.3m meshdish recieveing asiasat3s
My Location
melbourne,australia
hi mate can you please tell me from where i can download this programme Penta 1.11 or can you send me on raja*optusnet.com.au
thanks
 

Mickha

Super Moderator
Staff member
Joined
Dec 10, 2004
Messages
5,974
Reaction score
884
Points
113
My Satellite Setup
1.2M Channel Master, 1224 motor, VU+ Duo 2
My Location
North West
try a search on google for magictrance.nl click on the English version after entering the site, that should provide everything you require.
 
Top