Matrix Reborn

mumtazrizvi

Regular Member
Joined
Oct 23, 2004
Messages
87
Reaction score
0
Points
0
Age
64
My Location
Pakistan
Hi Dear Mates

Good Afternoon

Yesterday I converted my MRV to a Matrix Reborn using the
Cas Interface-II by updating the S/W MRT 1.8 but one sur-
prize I noticed in the Cam Menu there is "ZCAS" whereas it
has to be S/W 1.8 (just on experimental basis I tried it) On
every channel the cam says "insert smart card" any comment
in this regard will be highly appreciated.

With best regards/wishes

Mumtaz Rizvi :rolleyes:
 

rolfw

Believe it when I see it Admin.
Staff member
Joined
May 1, 1999
Messages
38,292
Reaction score
1,615
Points
113
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
Sounds like the conversion hasn't worked, are you sure it is possible?
 

mumtazrizvi

Regular Member
Joined
Oct 23, 2004
Messages
87
Reaction score
0
Points
0
Age
64
My Location
Pakistan
rolfw said:
Sounds like the conversion hasn't worked, are you sure it is possible?

Hi Dear Rolfw

Good Afternoon

No I am not sure but I tried because I was quite sure
if something wrong will happend I can reconvert it back
to MRV thatswhat I tried it. I read that there is a new
S/W MRT 1.9 before applying it the MRT 1.8 has to be
put in the MR/MRV. Now I am looking for 1.9 but despite
spending 2 long hours could not get success.

With best regards/wishes

Mumtaz Rizvi
 

rolfw

Believe it when I see it Admin.
Staff member
Joined
May 1, 1999
Messages
38,292
Reaction score
1,615
Points
113
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
Try either fookfiles.com or Toecutter's Den, the link is in Nobbly's Big Links, Satellite Forums section.
 

rizla

Regular Member
Joined
Sep 1, 2004
Messages
29
Reaction score
0
Points
0
Age
43
My Location
Reading
mumtazrizvi said:
Hi Dear Mates

Good Afternoon

Yesterday I converted my MRV to a Matrix Reborn using the
Cas Interface-II by updating the S/W MRT 1.8 but one sur-
prize I noticed in the Cam Menu there is "ZCAS" whereas it
has to be S/W 1.8 (just on experimental basis I tried it) On
every channel the cam says "insert smart card" any comment
in this regard will be highly appreciated.

With best regards/wishes

Mumtaz Rizvi :rolleyes:





Hi,



All you have to do is go into ZCAS menu. At the bottom of the menu list it says "Information". Select this option and type in a three-digit number that is included in the RELEASE-NOTES.txt of any Mrtv zip file. The number is "777".

After your receiver initiates the CAM again, it will no longer appear as ZCAS but MR T V1.08 or 1.09 if you use mrtv109. Although it seems to work even with my MR CAM it's unstable. After a few channel swaps something happens and the receiver says "Invalid CI module". If you have the original Mrv CAM I recomend you to use Mrv 2.19. Only difference I found is that Mrv 2.19 doesn't clear Cyfra+.


 
Top