metabox not warkig only on no warkig

N

nhf11sa

Member
Messages
7
Likes
0
#1
hiii

metabox not warkig only on no warkig O-no
 
A

Adnan265340000

Member
Messages
4
Likes
0
#5
nhf11sa said:
hiii

metabox not warkig only on no warkig O-no
hello ser
how are you
your metabox is display is always on
no problum
Trick
remove the cover and remove the 2 pcb power suplliy and resold the flash
after 5 minet you can on the metabox i hope its working fine
 
X

xfile

Member
Messages
9
Likes
0
#7
Dear friend..

***** not working..??


2 kind..

-->1. i guess that ur receiver has copied from the original H/W..
-->2. another problem..
 
M

metaboxlover

Member
Messages
1
Likes
0
#8
You have to Reset the flash....there is no way any more
agar ham bacheye tehrooni , bia pishe khodam
 
G

garabolud

Member
Messages
1
Likes
0
#9
hi
after i download dataloader to my reciever it is showing always on and it,s not working plz help me
mamnon man kharej az keshvar hastam be shoma ham dastrasi nadaram
aghar momkene baram farsi benevisid
 
J

john28_3

Member
Messages
5
Likes
0
#10
Please help me .

My Metabox is black color.
I changed software by loadar 5518 but this software was mistake
and flash memory damaged.
Always display is (ON).
I can't use of new loader.
I went to http://www.megaone.com/emetabox/software/jtag.jpg
and made a cable ( parllel pc to receiver ) for flash memory by map.
1- Power off receiver and removed cover and unplug wires of power supply and
front pannel .
2- I connected cable of parllel pc to receiver ( in box ).
3- I used of jkey dave 2.
but jkey didn't know .
Please help me .

aus_tt@yahoo.com

O-Ha
 
A

aa_762

Regular Member
Messages
31
Likes
0
#11
Hi John
1) Where can i find this loader 5518.
2) Is your "always ON" problem resolved or still facing same problem.

How to use Jtag software...Any detailed guide available at internet.

I want to upgrade my receiver (Metabox)
Rgrds

AA
 
N

nko

Member
Messages
6
Likes
0
#12
Once you have make the jtag cord,

- Remove the metabox cap
- Plug the LPT1 to the Jtag port (The grounds are near the front side of the metabox)
- Power on the metabox
- Launch Jkeys software
an error message must be appears
because the micro is notin mode bootstrap
=> Press OK
- At this step you must have to see the device ID and the device of the receiver
on jkeys IHM
- Power off the metabox
- push flash programming button
(a window appear)
- now You must connect the Reset pin to the ground (pin 10 of the schema)
- Power on the metabox
- Press OK and unconnect Pin 10 to ground immediatly
- The micro run in bootstrap mode and jkeys initialize the com
(If an error message appear, it's failed. try again)
- choose "4900" in the "IRD Model" combobox (it have the same flash as the metabox)
- To save the flash data you must press "read" button (full)
- To program the flash you must press "program" button (full)
and select the bin file that you want to program

That's all.

notice: For me that was not sufficient. My pb must be other that the flash program.
if somebody can help me...
 
H

hajar

Member
Messages
1
Likes
0
#13
now You must connect the Reset pin to the ground (pin 10 of the schema)


please witch pin 10 of the schema idont know it can you explain
thanks
 
Top