Need Help Relook 400

N

njbnellie

Member
Messages
5
Likes
0
My Satellite Setup
EMTECH 320 pvr
amd
My Location
TASMANIA
#1
:confused
I have a huge problem that i don't know where to start. I was installing "HL216_400_pal_usb_all_noboot" and my laptop locked up half way through installing it. Now all I get on the screen when I turn on the relook is 'BOOTING' and that is where is stops. I can access the relook through USB or Ethernet, have not tried serial yet. Is there a way of restoring original image to at least get it working again.
. I hope someone has some advice as I hope it is not buggered.

Cheers njbnellie:confused:-rofl2:eek:
 
S

stevenpc

Member
Messages
5
Likes
0
#2
I once had a powercut halfway threw installing and the only solution was to jtag i think that is your solution.
 
N

njbnellie

Member
Messages
5
Likes
0
My Satellite Setup
EMTECH 320 pvr
amd
My Location
TASMANIA
#3
Hi, thanks for that, as I'm relatively new to all this, it is probably a stupid question, what is a (JTAG) is it a piece of software and where do i find info on using it, I dont know anyone here in Tassie that can help me.
thanks in advance Njbnellie
 
S

stevenpc

Member
Messages
5
Likes
0
#4
simple explanation would be you have to reload the boot menu into the chip
a jtag is a lead that you connect to pc & to the board in the relook you then run the correct sw thats about it after that you are back to normal if you can contact me via pm i can give you more info.
 
N

njbnellie

Member
Messages
5
Likes
0
My Satellite Setup
EMTECH 320 pvr
amd
My Location
TASMANIA
#5
thanks for that, i can not seem to PM you,

cheers njbnellie
 
S

stevenpc

Member
Messages
5
Likes
0
#6
ive uoloaded the files and info to
_ttp://www.mediafire.com/?9u3tyyn3unm
download & unzip to a folder and have a good read instructions are included
you can ims me if you add me to msn messenger
 
N

njbnellie

Member
Messages
5
Likes
0
My Satellite Setup
EMTECH 320 pvr
amd
My Location
TASMANIA
#8
thanks for that, I'm not very good with an soldering iron, so being able to borrow one is great.


cheers njbnellie
 
M

macarmagh

Member
Messages
2
Likes
0
#9
njbnellie said:
:confused
I have a huge problem that i don't know where to start. I was installing "HL216_400_pal_usb_all_noboot" and my laptop locked up half way through installing it. Now all I get on the screen when I turn on the relook is 'BOOTING' and that is where is stops. I can access the relook through USB or Ethernet, have not tried serial yet. Is there a way of restoring original image to at least get it working again.
. I hope someone has some advice as I hope it is not buggered.

Cheers njbnellie:confused:-rofl2:eek:
Hi m8, had the same thing happen to me, laptop went to standby during image flash, just switched the receiver off using the switch at the back and switch on holding the power button at the front, startup flashtools, select usb and re-download your image.

As you can still connect to the receiver using a usb cable hopefully the above will work for you.

Mac.
 
N

njbnellie

Member
Messages
5
Likes
0
My Satellite Setup
EMTECH 320 pvr
amd
My Location
TASMANIA
#10
Thanks for that macarmagh, it worked. I managed to reflash highland onto the relook and it starts, I just have to figure oout what other software i need on the relook as i cant seem to get any sat feeds now.

cheers njbnellie:):-worship
 
M

macarmagh

Member
Messages
2
Likes
0
#11
Hi m8, glad you got your receiver working, not familiar with the Highland image but there's normally plenty of emulators and other bits of software available.

Mac.
 
D

deffc0n

Member
Messages
5
Likes
0
My Satellite Setup
DM8K/ET9100/DM800SE/VU+DUO
My Location
MULY
#12
I have still problem with my relook 400s.
I connect jtag and write new boot is ok only still no connect my pc and relook.
I push power when start relook and nothing :(
My pc no see relook !!
Any sugestion what is wrong ?
Why still no connect usb/serial port with my pc ?
I change difrent cable usb, change pc ( 2 laptops and 1 normal pc) and still no connect only on LCD USB UPGRADE.
Normal switch is still BOOTING.
I write all boot and this same problem co connect?
I want write by jtag image and i dont khnow why this do it ?
thx a lots :)
 
Top