New Edision OS nino Pro Grey 1x DVB-S2X + 1x DVB-C/T2 Linux Enigma 2 Combo Tuner Digital Multi-Stream Receiver H.265 HEVC HD 1080p

  • Thread starter World-of-Satellite
  • Start date
M

moonbase

Mini Dish Man
Messages
1,934
Likes
1,738
My Satellite Setup
1.25m Unicorn
My Location
UK
Following on from my post above re the Blind Scan, I checked an Automatic Scan with the Nino Pro and it proceeded to find 161 channels. However, after exiting the screens to go back to a picture I got an error message. After powering down the receiver and turning it back on it finally gave a picture. Is this type of behaviour normal for an E2 receiver?

Pics of the automatic scan result and the error message attached below. New Edision OS nino Pro Grey 1x DVB-S2X + 1x DVB-C/T2 Linux Enigma 2 Combo Tuner Digital Multi-Stream Receiver H.265 HEVC HD 1080p_1063171 New Edision OS nino Pro Grey 1x DVB-S2X + 1x DVB-C/T2 Linux Enigma 2 Combo Tuner Digital Multi-Stream Receiver H.265 HEVC HD 1080p_1063171 New Edision OS nino Pro Grey 1x DVB-S2X + 1x DVB-C/T2 Linux Enigma 2 Combo Tuner Digital Multi-Stream Receiver H.265 HEVC HD 1080p_1063171
 
scopus

scopus

Specialist Contributor
Messages
1,971
Likes
2,564
My Satellite Setup
Primesat/Famaval 1.8 PF C/ku/Ka, Octagon SX8HD1, SX88, Openbox S3 Mini HD-V8S Freesat V7 HD-V8 Finder, Amiko A4K Combo, Satlook Colour HD Spectrum, Sansui A909 Amp and BOSE Acoustimass speakers for the audio.
My Location
Staffs UK
Following on from my post above re the Blind Scan, I checked an Automatic Scan with the Nino Pro and it proceeded to find 161 channels. However, after exiting the screens to go back to a picture I got an error message. After powering down the receiver and turning it back on it finally gave a picture. Is this type of behaviour normal for an E2 receiver?

Pics of the automatic scan result and the error message attached below. View attachment 121082 View attachment 121083 View attachment 121084
Did you do anything with the satellite XML file? Sounds like something has corrupted..
 
M

moonbase

Mini Dish Man
Messages
1,934
Likes
1,738
My Satellite Setup
1.25m Unicorn
My Location
UK
No, I am using the satellites xml file that was shipped with the image.
 
M

moonbase

Mini Dish Man
Messages
1,934
Likes
1,738
My Satellite Setup
1.25m Unicorn
My Location
UK
Use a proper text editor, e.g. Notepad+. Currently you have broken the encoding. And why are you not using UTF8?

After editing the xml file upload it to www.xmlvalidation.com to check the mark up is correct.

Is the validation web site online, I tried to access it to check an xml file but I keep getting an "Error 524 Timeout" message?
 
stephan94

stephan94

Member
Messages
384
Likes
524
My Satellite Setup
1.20 Channel master ( Paris)and 1200 Laminas ( Bavaria) KU and C Band
Openbox SX6 and S3 Mini, Dr HD 15, Octagon SF 4008 and Octagon SX88and SX8 HD One, TBS 6983
My Location
Bavaria and Paris
Is the validation web site online, I tried to access it to check an xml file but I keep getting an "Error 524 Timeout" message?
maybe a problem with your firewall or your antivirus?
New Edision OS nino Pro Grey 1x DVB-S2X + 1x DVB-C/T2 Linux Enigma 2 Combo Tuner Digital Multi-Stream Receiver H.265 HEVC HD 1080p_1063208 here, no problem.
 
M

moonbase

Mini Dish Man
Messages
1,934
Likes
1,738
My Satellite Setup
1.25m Unicorn
My Location
UK
Back again.... :(

I created and downloaded a satellites.xml file from the web site of Huevos and validated it using the validation site, all OK. The new satellites xml file was FTP'd to the box using Filezilla to /etc/enigma2, Nino Pro rebooted and blind scan initiated on 40.5W C band. The blind scan found approximately 65 transponders and a channel scan of these transponders gave about 180 channels.

On pressing the green button to OK the completion of the channel scan the Nino Pro returned to the Open VIX screen with a please wait message and then returned an error message indication no data on the transponder. This is not correct, as other receivers give pictures for this transponder. The error message is not just restricted to this transponder, it applies to all transponders that were found on the blind scan. If I reboot the receiver I then get pictures !

Does this sound like a tuner fault or a firmware/software fault or is it normal for these E2 boxes?


New Edision OS nino Pro Grey 1x DVB-S2X + 1x DVB-C/T2 Linux Enigma 2 Combo Tuner Digital Multi-Stream Receiver H.265 HEVC HD 1080p_1063218
 
scopus

scopus

Specialist Contributor
Messages
1,971
Likes
2,564
My Satellite Setup
Primesat/Famaval 1.8 PF C/ku/Ka, Octagon SX8HD1, SX88, Openbox S3 Mini HD-V8S Freesat V7 HD-V8 Finder, Amiko A4K Combo, Satlook Colour HD Spectrum, Sansui A909 Amp and BOSE Acoustimass speakers for the audio.
My Location
Staffs UK
Back again.... :(

I created and downloaded a satellites.xml file from the web site of Huevos and validated it using the validation site, all OK. The new satellites xml file was FTP'd to the box using Filezilla to /etc/enigma2, Nino Pro rebooted and blind scan initiated on 40.5W C band. The blind scan found approximately 65 transponders and a channel scan of these transponders gave about 180 channels.

On pressing the green button to OK the completion of the channel scan the Nino Pro returned to the Open VIX screen with a please wait message and then returned an error message indication no data on the transponder. This is not correct, as other receivers give pictures for this transponder. The error message is not just restricted to this transponder, it applies to all transponders that were found on the blind scan. If I reboot the receiver I then get pictures !

Does this sound like a tuner fault or a firmware/software fault or is it normal for these E2 boxes?


View attachment 121089
Got to be that XML file. I would factory reset and try again, but leave the default XML in. Unless other E2 experts can help?
 
stephan94

stephan94

Member
Messages
384
Likes
524
My Satellite Setup
1.20 Channel master ( Paris)and 1200 Laminas ( Bavaria) KU and C Band
Openbox SX6 and S3 Mini, Dr HD 15, Octagon SF 4008 and Octagon SX88and SX8 HD One, TBS 6983
My Location
Bavaria and Paris
I think I understand where your problem comes from.
As soon as on a satellite there is a transponder in T2MI this problem can appear and causes an error which is only solved after a restart.
The 40 west has several frequencies in T2MI (4183L5000 - 4131L3750- 4126L3750-4112L3750 etc ....)
Try to make a blindscan only between 3600 and 3850 L and R and tell me if you still have this problem.
(I have the same problem on 40 ° East)
on the 4°9 East despite the T2MI this problem does not occur, but it is KU band ??
 
M

moonbase

Mini Dish Man
Messages
1,934
Likes
1,738
My Satellite Setup
1.25m Unicorn
My Location
UK
Got to be that XML file. I would factory reset and try again, but leave the default XML in. Unless other E2 experts can help?

The xml file was from the web site of Huevos and I also validated it with the online validator?
 
M

moonbase

Mini Dish Man
Messages
1,934
Likes
1,738
My Satellite Setup
1.25m Unicorn
My Location
UK
I think I understand where your problem comes from.
As soon as on a satellite there is a transponder in T2MI this problem can appear and causes an error which is only solved after a restart.
The 40 west has several frequencies in T2MI (4183L5000 - 4131L3750- 4126L3750-4112L3750 etc ....)
Try to make a blindscan only between 3600 and 3850 L and R and tell me if you still have this problem.
(I have the same problem on 40 ° East)
on the 4 ° 9 East despite the T2MI this problem does not occur, but it is KU band ??

Stephan,

OK, good idea and worth a try, I will give your suggestion a try now, back in 10 minutes.....
 
M

moonbase

Mini Dish Man
Messages
1,934
Likes
1,738
My Satellite Setup
1.25m Unicorn
My Location
UK
I think I understand where your problem comes from.
As soon as on a satellite there is a transponder in T2MI this problem can appear and causes an error which is only solved after a restart.
The 40 west has several frequencies in T2MI (4183L5000 - 4131L3750- 4126L3750-4112L3750 etc ....)
Try to make a blindscan only between 3600 and 3850 L and R and tell me if you still have this problem.
(I have the same problem on 40 ° East)
on the 4°9 East despite the T2MI this problem does not occur, but it is KU band ??

You were correct, it was the T2M1 transponders causing the issue. If they are not scanned in the receiver goes straight to the channels with pictures. Thank you for your suggestion.
 
stephan94

stephan94

Member
Messages
384
Likes
524
My Satellite Setup
1.20 Channel master ( Paris)and 1200 Laminas ( Bavaria) KU and C Band
Openbox SX6 and S3 Mini, Dr HD 15, Octagon SF 4008 and Octagon SX88and SX8 HD One, TBS 6983
My Location
Bavaria and Paris
Hopefully the devellopeurs will solve this problem .
Huevos wrote that it was not certain at all, because it is very special.
We can only hope.
 
Top