Power when U need it

dig deep

Prince of Birthdays
Staff member
Joined
Sep 28, 2005
Messages
8,972
Reaction score
424
Points
83
My Satellite Setup
Dream7020 and AZ Elite and a few DM800
My Location
Sweden
The most Powerful Diesel Engine in the World!

The Wartsila-Sulzer RTA96-C turbocharged two-stroke diesel engine is the most powerful and most efficient prime-mover in the world today. The Aioi Works of Japan's Diesel United, Ltd built the first engines and is where some of these pictures were taken.

It is available in 6 through 14 cylinder versions, all are inline engines. These engines were designed primarily for very large container ships. Ship owners like a single engine/single propeller design and the new generation of larger container ships needed a bigger engine to propel them.

The cylinder bore is just under 38" and the stroke is just over 98". Each cylinder displaces 111,143 cubic inches (1820 liters) and produces 7780 horsepower. Total displacement comes out to 1,556,002 cubic inches (25,480 liters) for the fourteen cylinder version.


Some facts on the 14 cylinder version:
Total engine weight:

2300 tons (The crankshaft alone weighs 300 tons.)


Length:
89 feet


Height:
44 feet


Maximum power:
108,920 hp at 102 rpm


Maximum torque:
5,608,312 lb/ft at 102rpm

Fuel consumption at maximum power is 0.278 lbs per hp per hour (Brake Specific Fuel Consumption). Fuel consumption at maximum economy is 0.260 lbs/hp/hour. At maximum economy the engine exceeds 50% thermal efficiency. That is, more than 50% of the energy in the fuel in converted to motion. For comparison, most automotive and small aircraft engines have BSFC figures in the 0.40-0.60 lbs/hp/hr range and 25-30% thermal efficiency range. Even at its most efficient power setting, the big 14 consumes 1,660 gallons of heavy fuel oil per hour.

The internals of this engine are a bit different than most automotive engines. The top of the connecting rod is not attached directly to the piston. The top of the connecting rod attaches to a "crosshead" which rides in guide channels. A long piston rod then connects the crosshead to the piston. I assume this is done so the sideways forces produced by the connecting rod are absorbed by the crosshead and not by the piston. Those sideways forces are what makes the cylinders in an auto engine get oval-shaped over time.


Installing the "thin-shell" bearings. Crank & rod journals are 38" in diameter and 16" wide:
The crank sitting in the block (also known as a "gondola-style" bedplate). This is a 10 cylinder version.
Note the steps by each crank throw that lead down into the crankcase:
A piston & piston rod assembly. The piston is at the top. The large square plate at the bottom is where the whole assembly attaches to the crosshead:

 

Lancelot

Retired Mod
Joined
Jun 1, 2004
Messages
3,639
Reaction score
10
Points
38
My Satellite Setup
SS1.
125cm Gibbi with Channelmaster feedhorn and Inverto C120 twin.
36v H to H 62E - 61.5W
My Location
South central
The figures are as difficult to take in as the scale of the thing. I think pic 2 says it all.


L.:)
 

rolfw

Believe it when I see it Admin.
Staff member
Joined
May 1, 1999
Messages
38,292
Reaction score
1,615
Points
113
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
Certainly is impressive. :)
 

BadWithComputer

The Local Drunkard
Joined
Aug 19, 2005
Messages
646
Reaction score
0
Points
16
Age
33
My Satellite Setup
30MB ADSL ONO, Spain
32" Internet connected TV
Many Satellite Dishes.
Humax HD Freesat Box
My Location
Spain
A few more of them and a new system of nuclear power plants should be obsolete!
 
Top