Technomate 9100 JTAG

Llew

cerca trova...
Staff member
Joined
Jan 1, 2000
Messages
16,226
Reaction score
4,197
Points
113
Age
81
My Satellite Setup
Triple Dragon, Dreambox 8000, Echostar AD3000ip, TBS6522,6925,6983 PCie cards.
Gibertini 1.25m motorised dish driven by the AD3000, with either Inverto BU Quad or Norsat / XMW Ka LNBs . SMW 1.05m + 3 other dishes. Speccy: Promax HD Ranger+
My Location
The Flatlands of East Anglia
If all goes bellyup, repair your corrupted flash using this JTAG option.

Llew
 

Attachments

  • Technomate_TM9100_JTAG.zip
    231.3 KB · Views: 674

rolfw

Believe it when I see it Admin.
Staff member
Joined
May 1, 1999
Messages
38,292
Reaction score
1,615
Points
113
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
Hope this doesn't become the most popular sticky Llew. :)
 

Llew

cerca trova...
Staff member
Joined
Jan 1, 2000
Messages
16,226
Reaction score
4,197
Points
113
Age
81
My Satellite Setup
Triple Dragon, Dreambox 8000, Echostar AD3000ip, TBS6522,6925,6983 PCie cards.
Gibertini 1.25m motorised dish driven by the AD3000, with either Inverto BU Quad or Norsat / XMW Ka LNBs . SMW 1.05m + 3 other dishes. Speccy: Promax HD Ranger+
My Location
The Flatlands of East Anglia
Well, judging from various forum posts, there could be a run on JTAG interfaces :-rofl2

Llew
 

rolfw

Believe it when I see it Admin.
Staff member
Joined
May 1, 1999
Messages
38,292
Reaction score
1,615
Points
113
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
Must switch mine on again over the weekend, but I think I'll bring a portable in to connect it to, so that I can watch something on the main TV while it is constantly rebooting. :-lmao
 

wod

Regular Member
Joined
Aug 7, 2005
Messages
4,213
Reaction score
238
Points
63
My Satellite Setup
1m channel master, jaeger smr1224, Inverto black ultra twin, technomate tm-1500ci, broken receiver vantage x221ci, New additions Skybox F5s and technomate tm-5402 HD arriving soon.
My Location
yorkshire
not had a problem with mine at all, you just need to find a good image, i have found that juliet 006 image works best for me
 

saldasyl

Member
Joined
Jul 29, 2006
Messages
26
Reaction score
0
Points
0
Age
39
My Satellite Setup
connected ot hotbird and sky
My Location
England
is there a jtag solution for dm 500 . mine keeps rebooting at startup screen. even with original firmware!
 

tt786

Member
Joined
Jul 1, 2007
Messages
2
Reaction score
0
Points
0
Age
47
My Satellite Setup
ss1,tm 9100 ,motor 80cm dish
My Location
northwest
anyone know how to do this jtag flash ?

the guide with it says how to install the software
but it dont say how to use it ?

its reboot you pc and ¡°portTalk¡± will start after rebooting

but nothing happens

if i click the exe a black box pops up for a second and thats it
no flash no nothing

it dosnt even say if the box should be switch on or not
anyone shed some light on this ?
 

rolfw

Believe it when I see it Admin.
Staff member
Joined
May 1, 1999
Messages
38,292
Reaction score
1,615
Points
113
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
Normally to use a JTAG flash, you need a JTAG connector onto the motherboard, don't think you can do it via a serial port.
 

tt786

Member
Joined
Jul 1, 2007
Messages
2
Reaction score
0
Points
0
Age
47
My Satellite Setup
ss1,tm 9100 ,motor 80cm dish
My Location
northwest
yes mate it can only be done via a parallel port direct to the mother board of the sat box

in short. setup the lead and software and parallel port
as in the pdf and read me of the software LTP1 mode normal 378

rename main exe to bootloader.exe

switch on your already connected via jtag box and

open a command window type "cd" and leave 1 space and then drag
bootloader.exe on to the command window

edit the text that appears and remove this off the end
"\bootloader.exe" and hit enter
now you will find your at the correct path

al you need do now is type " bootloader.exe 9600 "
and the program will start



thanks to baz for working it out for everyone
 
Top