Update of UCAS embedded

D

Dimitris

Member
Messages
3
Likes
0
#1
Dear all,



I have registered in your forum and had a look around. Congratulations. I have a small question. I have a fortecstar 6000 with ucas embedded. In the menu, the version says MR 1.08. How can update that?. I know there is an Ucas programer that can be purchased for that reason but is this going into the slot where the module normaly is? Or can I update it directly with a nullmodem cable from the pc to the back of the receiver?



Please let me know if this post has been replied at the past and if so please provide the link to that post.



Thanks



Dimitris
 
D

Dimitris

Member
Messages
3
Likes
0
#2
Dear All,



Can someone provide me with a step-by-step procidure of what I need to update my above-mentioned UCAS? Please?
 
john_graydon

john_graydon

Regular Member
Messages
2,219
Likes
3
My Satellite Setup
Azbox premium HD+,Dusty Dreambox 7000s,& Sky HD.
My Location
Dublin....Ireland
#3
Dimitris said:
Dear All,



Can someone provide me with a step-by-step procidure of what I need to update my above-mentioned UCAS? Please?

Just to say you wont be able to update your cam with a null modem cable. Your 2nd question not too sure about on your cam Think you have Matrix reloaded, loaded so you will need a ucas board like the magic cam one. But not the exact same one if you get my drift. You will need to download a loader programme to load the latest software. Just replying to your q as nobody else has. not an expert on this YET. lol
 
G

Gustavo Hoffmann

Regular Member
Messages
45
Likes
0
My Location
it prepares the Magic Cam, or either to leave in dremload
#4
Hi!
I've just bought a Manhattan Starlight 6900 with embedded Ucas. In slot A does not have anithing in it and says "Not Installed". Was wondering how are you able to access the embedded ucas as it will not let me select the 2 embedded option in the CA Setup menu. Do I wave to load on the firmware first or should this be already on?
In the menu information system appears:
Boot Version: 2.01
APPL Version: 3.06AP
C.A. Version: 3.03M
E does not open no field i to type something!
Thanks!
Gustavo
 
G

Gustavo Hoffmann

Regular Member
Messages
45
Likes
0
My Location
it prepares the Magic Cam, or either to leave in dremload
#5
Hi Dimitris!
To activate Ucas Embedded you have to follow these steps:
Go into SYSTEM INFORMATION
Type in 1212
Turn RX into STANDBY
Turn back ON and it will be installed.
Gustavo Hoffmann/Brasil
 
G

Gustavo Hoffmann

Regular Member
Messages
45
Likes
0
My Location
it prepares the Magic Cam, or either to leave in dremload
#6
it would like an aid! I am trying to program ucas embedded of decoder Manhattan Starlight 6900.

it appears the message:

removed handle or baudrate highly too much for this STB. Please he tries another time. Erasing given old, he waits please!

The Ucas embedded already is activated!

But I want to leave in dreamload stops later transforming into Magic Cam!

what I have that to make to correct?
 
F

f1167

Member
Messages
12
Likes
0
#7
Gustavo Hoffmann said:
Hi Dimitris!
To activate Ucas Embedded you have to follow these steps:
Go into SYSTEM INFORMATION
Type in 1212
Turn RX into STANDBY
Turn back ON and it will be installed.
Gustavo Hoffmann/Brasil
please have you information about skybox3000
is the stb has UCAS embeded or no ?
thanks
 
G

Gustavo Hoffmann

Regular Member
Messages
45
Likes
0
My Location
it prepares the Magic Cam, or either to leave in dremload
#8
the receiver skybox 3000 does not have ucas embedded!
 
Top