Recent content by Bthree

  1. B

    Irdeto CI Cam identification

    Hi rolfw, Wow that was quick, i have flashed a few cams in the past but have never seen any cam that does not have a part No or marking of some type. Just being careful, i may leave this one as is. Regards,
  2. B

    Irdeto CI Cam identification

    Hello, I have recently purchased an Irdeto CI cam which in every way electrical resembles a PN 90440. Irdeto Common Interface Ver: 00:04 Softcell: Ver 2.06(CI) -NEC I-Chip Compiled Jun 25 1999 14:30:31 The front of the cam has no warning The back of the Cam has all the standard markings but...
  3. B

    Seca 2, did they crack it?

    Well Rolf, The phrase "using information gained from their attacks to crack an encryption system called SECA2" decripts by me to mean they used the information gained from snooping to decipher the Seca2 system but as with all news articles they will be written to suit a purpose, in this case...
  4. B

    Last hope: Schematic diagram of Freecam?

    Lets see... you did put the flashram in the right way, ie dot for pin one the same way it came out. With a multimeter check all pins resistance to earth should be the same for all data lines and a different reading for all address lines. Take the flashram off, check the program and resolder it...
  5. B

    seca cam and seca 2 !!!

    I have an Aston 1.03 and a 1.05 CI cam will either of these work with Seca2 and a current Sub card please ? Bthree.
  6. B

    what version

    [updated:LAST EDITED ON 24-Dec-01 AT 09:23 AM (GMT)]cozzy, Look back on previous posts there is one a little way back, not very far that explains most CI cam versions, yours is amongst them. The bit you should be most interested in as a little statement that says your cam is one time flashable...
  7. B

    CAM Help

    This CA CAM is not flashable and will not fit in a Laptop (too Thick) in fact CA cam's from a Nokia9200/9500/dbox are not flashable. To do an upgrade you have to do a hardware modification, i am sure if you look back there is information on this subject, even on other forums possibly under...
  8. B

    Irdeto CI CAMs - what's what

    [updated:LAST EDITED ON 16-Dec-01 AT 00:09 AM (GMT)]Hello 2old4this, Found this on a newsgroup posted by a reputable retailer. Now in Stock for immediate Despatch Irdeto Blue CI CAM P/N 901633 Version 4.7SE Softcell V 2.06 Compiled Jun25 1999 Fully Reflashable by .bin or .sbr These are Factory...
  9. B

    Which cam do I have?

    ilpresident, You cannot flash the older CA Cam what we are talking about here is a physical task. As you say when the cam is open all components are surface mount, you have to locate the 27C512 eprom and unsolder it from the board, buy a new OTP 27C512 eprom and program it in a specialised...
  10. B

    Which cam do I have?

    2old, you are correct in what you say, the older CA Cam must have the 27C512 eprom physically removed and reprogrammed, Amon 2.1 or 2.2 would be OK. This will give you I/S/V on a nokia 9200,9500,dbox by installing DVB2000 as well. A recent topic explains this in a link. ipres It must be...
  11. B

    eurocam 2 ,,the final questions :+

    I have battled with this issue in the recent past gave up and bought a older series one 00.03 CIcam and flashed it to freeCAM2-106 and solved my problem but from what i gathered the Australian varient of the Euro 1.06 will only do provider 10 and not PR00. Our Euro friends will be able to...
Top