Log in
Register
Menu
Log in
Register
Home
What's new
Latest activity
Authors
Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Current visitors
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Satellite TV receivers & systems support forums
Receiver software, international Section
Technomate 1500 CI+ Switching off
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Zorch" data-source="post: 791968" data-attributes="member: 262469"><p>Hi Satknight,</p><p></p><p>Perhaps this problem can be solved by simply re-flashing the receiver... sometimes remnants of old software can remain (floating around) and this can cause all kinds of strange issues to arise...</p><p></p><p>The steps below detail the correct procedure for flashing new 'Official Software' onto the TM 1500 CI+ (If you already use this exact procedure... then please disregard this post)</p><p></p><p>1/ Connect TM 1500CI+ to PC with RS232 Null Modem Cable (as normal)</p><p></p><p>2/ Remove F-connector/feed from dish to receiver (optional but advised)</p><p></p><p>3/ Use your loader program to Upload an NDF file (all current stored satellites/channels/settings etc.) from the receiver to your PC</p><p></p><p>4/ Go into the Menu of receiver > System Settings > Factory Reset > PIN 0000 > Factory Reset</p><p></p><p>5/ Download the new 'Official Software' file to the receiver (make sure the 'Finish' button is clicked at the end of the download)</p><p></p><p>6/ Go into the menu of receiver > System Settings > Factory Reset > PIN 0000 > Factory Reset</p><p></p><p>7/ Go back into the Menu of receiver > 'System Information' and check the date on screen corresponds with the date of the 'Official Software' file</p><p></p><p>8/ Use your loader program to Download the NDF file (all current stored satellites/channels/settings etc.) back onto the receiver from your PC</p><p></p><p>9/ Switch the receiver 'Off' using the power switch on the rear of the unit</p><p></p><p>10/ Re-attach F-connector/feed from dish to receiver... then switch the receiver back on again using the power switch on the rear of the unit</p><p></p><p>11/ Go into menu > System Settings and reset the following sub-menus to your own personal preferences...</p><p></p><p>Time/Date Setting</p><p>A/V Output Setting</p><p>OSD Setting</p><p>Password Setting</p><p></p><p>12/ Lastly... don't forget to press the (+) Volume Control button on the remote to reset the audio level to 100% (or to your own personal preference)</p><p></p><p>I hope this helps...</p><p></p><p>Best Wishes,</p><p>Zorch</p></blockquote><p></p>
[QUOTE="Zorch, post: 791968, member: 262469"] Hi Satknight, Perhaps this problem can be solved by simply re-flashing the receiver... sometimes remnants of old software can remain (floating around) and this can cause all kinds of strange issues to arise... The steps below detail the correct procedure for flashing new 'Official Software' onto the TM 1500 CI+ (If you already use this exact procedure... then please disregard this post) 1/ Connect TM 1500CI+ to PC with RS232 Null Modem Cable (as normal) 2/ Remove F-connector/feed from dish to receiver (optional but advised) 3/ Use your loader program to Upload an NDF file (all current stored satellites/channels/settings etc.) from the receiver to your PC 4/ Go into the Menu of receiver > System Settings > Factory Reset > PIN 0000 > Factory Reset 5/ Download the new 'Official Software' file to the receiver (make sure the 'Finish' button is clicked at the end of the download) 6/ Go into the menu of receiver > System Settings > Factory Reset > PIN 0000 > Factory Reset 7/ Go back into the Menu of receiver > 'System Information' and check the date on screen corresponds with the date of the 'Official Software' file 8/ Use your loader program to Download the NDF file (all current stored satellites/channels/settings etc.) back onto the receiver from your PC 9/ Switch the receiver 'Off' using the power switch on the rear of the unit 10/ Re-attach F-connector/feed from dish to receiver... then switch the receiver back on again using the power switch on the rear of the unit 11/ Go into menu > System Settings and reset the following sub-menus to your own personal preferences... Time/Date Setting A/V Output Setting OSD Setting Password Setting 12/ Lastly... don't forget to press the (+) Volume Control button on the remote to reset the audio level to 100% (or to your own personal preference) I hope this helps... Best Wishes, Zorch [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Satellite TV receivers & systems support forums
Receiver software, international Section
Technomate 1500 CI+ Switching off
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top