1mtr motorised dish setup

Archived-1

Archived-1

Persona non grata
My Location
uk
hi, I am going to make a start on putting my 1mtr back up today, ive just been outside and decided on its new location and this is were she will rest,

just going out to get some fixing, and I will post pictures along the way, if the rain holds off :-0.
 

Attachments

  • 1mtr setup.webp
    1mtr setup.webp
    61.4 KB · Views: 229
ive been and picked the bits up a pair of 12 t/k brackets all fixings 2 f connectors and 20mtr of wf100 18 pound, i just need to find my angle grinder and take the top of the cloths post that i am using as a pole, line it up and i am ready for the dish :-),

just going to have some dinner and i will go and finish it off.
 

Attachments

  • DSCN3423.webp
    DSCN3423.webp
    72.9 KB · Views: 157
Ah, proper job: Dinner then Tea, not Lunch then Dinner.
 
Tivù said:
Ah, proper job: Dinner then Tea, not Lunch then Dinner.

Is the 1m to be motorised?
Click to expand...
i thought the thread title would give it away lol yes tivu it will be motorized m8 :-)
 
It did - I just failed to notice!

Too busy chomping Egg & Cress Butties for Dinner.................
 
just having a fag break then ready for cabling/lining up, i am going to swing the dish as far east as it will go then lower the dish so it just misses the shed roof, then clip up job done :-).
 

Attachments

  • DSCN3424.webp
    DSCN3424.webp
    51.6 KB · Views: 258
  • DSCN3426.webp
    DSCN3426.webp
    23.3 KB · Views: 221
Interesting motor mount, which make is it ?
 
Think that's a stab?
 
not sure what motor it is wod tbh, just going to clip the cables up, I will see if it says anything on it, it does save time setting up compared to the other type plus it can only move on the pole with it been fixed to the dish, it cost me about 100 pounds 5/6 years ago.
 
all sorted, a few pictures of both dishes both @ 0.8W, I just need a 1.8 now :-).
 

Attachments

  • DSCN3430.webp
    DSCN3430.webp
    67.7 KB · Views: 241
  • DSCN3431.webp
    DSCN3431.webp
    86.9 KB · Views: 281
  • DSCN3428.webp
    DSCN3428.webp
    25.7 KB · Views: 256
  • DSCN3432.webp
    DSCN3432.webp
    25.2 KB · Views: 215
Nice install ;)
Motor looks like a Stab Cryptik for Orbital dishes.


Sent from my iPhone using Tapatalk
 
satelliteman said:
Nice install ;) Motor looks like a Stab Cryptik for Orbital dishes. Sent from my iPhone using Tapatalk
Click to expand...
yes cryptic rings a bell thanks, and it is an orbital dish that's on it.
 
Good stuff Martin,your neighbours cool with it all? I would be!!! Nice work. :cool:
 
yes they seem fine about it paul ones just given me a receiver :-) the 1.2 is hard to see from any garden but the 1.8 will be living there (when I get it) and move the 1.2 to the right, the 1mtr needs dropping a foot, I am going to get them air spayed brick style at some point though.
 
Nice setup that, it looks very exposed but a very sturdy mount!
 
martin-f said:
I am doing quite well with her I am hitting 37.5w to 57e atm very pleased :-).
Click to expand...
You know one day you'll actually WATCH some tv!!! :-smile3
 
Doubt it - there's never much on.
 
Maybe he should check out conad tv!!!
 
Back
Top