Log in
Register
Menu
Log in
Register
Home
What's new
Latest activity
Authors
Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Current visitors
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Satellite Tv Encryption Decryption
Cards, Programmers and Cams
X-CAM, Ultra CAM, Dragon CAM, Diablo, T Rex
Dragon CAM Predator update HELP !!!
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Mickha" data-source="post: 107474" data-attributes="member: 187442"><p>Hi genius5000,</p><p>I've only used a Fun 7 card as a loader, but I think you need to load it using the Dragon loader software.</p><p>These are the instructions for the Infinity/Phoenix USB but should be similar.</p><p>You need to put the programmer into 6Mhz mode to load the F84a card, unless the card has Fun 7 written on it.</p><p>You need:</p><p>-Smartmouse compatible card programmer</p><p>-The dragonload.exe program</p><p>_http://www.ucassupport.nl/dragonsupport/english/Software.htm</p><p></p><p>Make sure the programmer is in 6 MHz mode</p><p>Do not insert card until you start your programmer. DO NOT allow the programmer to auto detect the loader card. </p><p>The card goes into the programmer chip face down but into your Dragon Cam chip face up.</p><p>Start “Dragonload.exe”</p><p>By pressing the "Settings" button, you can change from com1 to com2</p><p>Then you need the Dragon loader card inserted in the Infinity USB programmer before you press connect otherwise you will get the message “Unable to Connect, check setting, programmer and card” </p><p>Press “Program card” point program to the Predator311.dra and click on it. Found in C: Unzipped Predator 311.</p><p>-The card will now be loaded.</p><p></p><p>When the card is loaded follow these instructions exactly, failure to do so could result in you damaging your Cam.</p><p></p><p>If your Cam is not in the receiver. Make sure your receiver is tuned to a FTA channel, switch off your receiver. Insert the programmed card into the Dragon module. Insert this into your receiver and turn on the receiver. </p><p>If your Dragon Cam is already in your receiver, tune to a FTA channel, I always use BBC news.</p><p>Turn off your receiver.</p><p>Insert the card, chip face up.</p><p>Turn on your receiver.</p><p>Go to the Common interface menu on the receiver, and select the "Dragon Loader" module.</p><p>In the next menu, select "yes, Load module".</p><p>Now a menu appears indicating that loading is in progress. To see the actual porgress percentage, select "refresh". There is no auto-refresh because some receivers had problems with that....</p><p>When loading is complete, a menu appears saying "Loading successful". <strong>REMOVE the loader card from the module.</strong></p><p>Turn off your receiver.</p><p>Now turn on your receiver and your Dragon Cam should be updated.</p><p>If you experience any problems please post back.</p><p>Best wishes</p><p>Mickha</p></blockquote><p></p>
[QUOTE="Mickha, post: 107474, member: 187442"] Hi genius5000, I've only used a Fun 7 card as a loader, but I think you need to load it using the Dragon loader software. These are the instructions for the Infinity/Phoenix USB but should be similar. You need to put the programmer into 6Mhz mode to load the F84a card, unless the card has Fun 7 written on it. You need: -Smartmouse compatible card programmer -The dragonload.exe program _http://www.ucassupport.nl/dragonsupport/english/Software.htm Make sure the programmer is in 6 MHz mode Do not insert card until you start your programmer. DO NOT allow the programmer to auto detect the loader card. The card goes into the programmer chip face down but into your Dragon Cam chip face up. Start “Dragonload.exe” By pressing the "Settings" button, you can change from com1 to com2 Then you need the Dragon loader card inserted in the Infinity USB programmer before you press connect otherwise you will get the message “Unable to Connect, check setting, programmer and card” Press “Program card” point program to the Predator311.dra and click on it. Found in C: Unzipped Predator 311. -The card will now be loaded. When the card is loaded follow these instructions exactly, failure to do so could result in you damaging your Cam. If your Cam is not in the receiver. Make sure your receiver is tuned to a FTA channel, switch off your receiver. Insert the programmed card into the Dragon module. Insert this into your receiver and turn on the receiver. If your Dragon Cam is already in your receiver, tune to a FTA channel, I always use BBC news. Turn off your receiver. Insert the card, chip face up. Turn on your receiver. Go to the Common interface menu on the receiver, and select the "Dragon Loader" module. In the next menu, select "yes, Load module". Now a menu appears indicating that loading is in progress. To see the actual porgress percentage, select "refresh". There is no auto-refresh because some receivers had problems with that.... When loading is complete, a menu appears saying "Loading successful". [b]REMOVE the loader card from the module.[/b] Turn off your receiver. Now turn on your receiver and your Dragon Cam should be updated. If you experience any problems please post back. Best wishes Mickha [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Satellite Tv Encryption Decryption
Cards, Programmers and Cams
X-CAM, Ultra CAM, Dragon CAM, Diablo, T Rex
Dragon CAM Predator update HELP !!!
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top