Log in
Register
Menu
Log in
Register
Home
What's new
Latest activity
Authors
Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Current visitors
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Satellite TV receivers & systems support forums
Receiver software, international Section
Fortecstar 5600ii H/w ? S/w?
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="nopfusch" data-source="post: 494498" data-attributes="member: 195487"><p>I have several AV sources in my home:</p><p>2 SAT receivers, 2 VCR's, and a DVD/VCR. All have programmable UHF modulators (PAL - I) from 21 to 68 . </p><p>All outputs are "in series" (UHF in-out) via an RG6 cable and then passed on to the 3 TV's.</p><p>Now between one used channel and the next I programmed the outputs from the various sources, that I have always two unused channels in between, to avoid cross-interference from one to the next channel.</p><p>E.G. source 1 channel 21</p><p>source 2 channel 24</p><p>source 3 channel 27</p><p>etc.</p><p>Now I wanted to add the newly aquired FORTECSTAR FSCO-5600II in to that series set-up. Again I left 2 channel space between the last channel number and the FSCO-5600.</p><p>But the TV's show when looking to the output produced by that FSCO-</p><p>5600, about 8 to 9 horizontal dark bars, about 6-8 cm high moving not too slow from bottom up over the screen. When the FSCO-5600 is used as stand-alone, it works fine. Only when used in that "UHF Network", the TVs show these bars. The other channels from other sources are not affected.</p><p>I tried another channel number output, with 6 empty channels in between the previous one, no improvement.</p><p>Anybody had similar experiences and what were the solutions, please?</p><p>Otherwise this is a fine receiver.</p></blockquote><p></p>
[QUOTE="nopfusch, post: 494498, member: 195487"] I have several AV sources in my home: 2 SAT receivers, 2 VCR's, and a DVD/VCR. All have programmable UHF modulators (PAL - I) from 21 to 68 . All outputs are "in series" (UHF in-out) via an RG6 cable and then passed on to the 3 TV's. Now between one used channel and the next I programmed the outputs from the various sources, that I have always two unused channels in between, to avoid cross-interference from one to the next channel. E.G. source 1 channel 21 source 2 channel 24 source 3 channel 27 etc. Now I wanted to add the newly aquired FORTECSTAR FSCO-5600II in to that series set-up. Again I left 2 channel space between the last channel number and the FSCO-5600. But the TV's show when looking to the output produced by that FSCO- 5600, about 8 to 9 horizontal dark bars, about 6-8 cm high moving not too slow from bottom up over the screen. When the FSCO-5600 is used as stand-alone, it works fine. Only when used in that "UHF Network", the TVs show these bars. The other channels from other sources are not affected. I tried another channel number output, with 6 empty channels in between the previous one, no improvement. Anybody had similar experiences and what were the solutions, please? Otherwise this is a fine receiver. [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Satellite TV receivers & systems support forums
Receiver software, international Section
Fortecstar 5600ii H/w ? S/w?
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top