Log in
Register
Menu
Log in
Register
Home
What's new
Latest activity
Authors
Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Current visitors
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Satellite TV receivers & systems support forums
DISH SETUP: Single sat, Multi-Sat & Motorised
help with getting a monoblock working with technomate
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="subhi" data-source="post: 189137" data-attributes="member: 208392"><p>hi all,</p><p></p><p>need some pointers on how to get my monoblock working with hotbird 13E and astra 19.2E</p><p></p><p>It's a DIY job 80cm dish with inverto 0.3dB monoblock pointing at hotbird for sure (not sure if it's working with astra atm)</p><p></p><p>I have replaced the receiver I had from Lidl (Silvercrest SL65) with technomate TM-1500CI+ </p><p></p><p>basically on the silvercrest could only see hotbird channels around 900 of them and couldn’t see any astra channels , with the technomate I can't figure out how to make it use both feeds under astra it can find around 700 channels, under hotbird it can find around 300, if I use autoscan it complains that channels memory is full after doing astra and half of the transponders on hotbird.</p><p></p><p>The question is , how do i configure the LNB ? DISEqC 1.0, 1.1 or 1.2, according to the specs (<a href="http://www.ftacom.com/UploadImages/is2.jpg" target="_blank">http://www.ftacom.com/UploadImages/is2.jpg</a>) it uses DISEqC 1.2 but the LNB only gives signal status when i switch DISEqC 1.0 on, and even then it gives identical signal strength for hotbird and astra.</p><p></p><p>any pointers would be greatly appreciated. this is a link to the photo of the dish and alignment <a href="http://photos.subhi.com/c939330.html" target="_blank">http://photos.subhi.com/c939330.html</a></p></blockquote><p></p>
[QUOTE="subhi, post: 189137, member: 208392"] hi all, need some pointers on how to get my monoblock working with hotbird 13E and astra 19.2E It's a DIY job 80cm dish with inverto 0.3dB monoblock pointing at hotbird for sure (not sure if it's working with astra atm) I have replaced the receiver I had from Lidl (Silvercrest SL65) with technomate TM-1500CI+ basically on the silvercrest could only see hotbird channels around 900 of them and couldn’t see any astra channels , with the technomate I can't figure out how to make it use both feeds under astra it can find around 700 channels, under hotbird it can find around 300, if I use autoscan it complains that channels memory is full after doing astra and half of the transponders on hotbird. The question is , how do i configure the LNB ? DISEqC 1.0, 1.1 or 1.2, according to the specs ([url]http://www.ftacom.com/UploadImages/is2.jpg[/url]) it uses DISEqC 1.2 but the LNB only gives signal status when i switch DISEqC 1.0 on, and even then it gives identical signal strength for hotbird and astra. any pointers would be greatly appreciated. this is a link to the photo of the dish and alignment [url]http://photos.subhi.com/c939330.html[/url] [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Satellite TV receivers & systems support forums
DISH SETUP: Single sat, Multi-Sat & Motorised
help with getting a monoblock working with technomate
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top