Log in
Register
Menu
Log in
Register
Home
What's new
Latest activity
Authors
Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Current visitors
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Satellite TV receivers & systems support forums
Satellite Systems - What to Buy - What to install
New diseqc motor to replace technomate tm 2600 h-h
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Tururu" data-source="post: 1075298" data-attributes="member: 227656"><p>It looks like the one I have SG2100 / FTE Dimo120+</p><p>The engine reset must be done while the engine is at 0º.</p><p>The engine takes the reference and if you use usals, perfect.</p><p>If it is not at 0º when resetting, part of that position as if it were zero.</p><p>In the tuner configuration VU+Solo2 you have engine options, inside you have an option.</p><p>Go to ....</p><p>When you put on top you will see that the green box puts <strong>Go to 0, press the green button. </strong></p><p>If all is well, the motor will be positioned at zero of the screen printing (reset now).</p><p>If it does not move, using the button as indicated by the partner, position it to zero.</p><p>When the power is ok, it turns on and green, when orders arrive by the cable (diseqc/usals commands), the LED flashes orange, if it locks and does not move, it can flash red/green all the time.</p><p>Before zeroing the engine and using the button, send the antenna several times from side to side, over time it becomes somewhat stiff and costs.</p><p>If you see that it is not going, it will pull and you did not release the button, the LED goes out, check the connectors, some are not well and you have problems with the power supply.</p><p>If it does not move with the button, insert external power as indicated by Trust1, from 13 to 18 Volts of continuous (VDC).</p><p>With 1 amp left over, negative to the chassis and positive to the center.</p><p></p><p>Luck</p><p>----------</p><p>Se parece al que tengo SG2100/FTE DIMO120+</p><p>El reset al motor se tiene que hacer estando el motor a 0º.</p><p>El motor toma la referencia y si usas usals, perfecto.</p><p>Si no esta a 0º al hacer el reset, parte de esa posicion como si fuera cero.</p><p>En la configuracion del sintonizador VU+Solo2 tienes opciones del motor, dentro tienes una opcion.</p><p>Ir a ....</p><p>Al ponerte encima veras que el cuadro verde pone<strong><span style="color: rgb(0, 0, 0)"> Ir a 0, pulsa el boton verde.</span></strong></p><p>Si todo esta bien, el motor se posicionara en el cero de la serigrafia. (reset ahora).</p><p>Si no se mueve, usando el boton como indca el compañero, posicionar a cero.</p><p>Cuando la alimentacion esta ok, se enciende el verde, al llegar ordenes por el cable (comandos diseqc/usals), el led parpadea en naranja, si se bloque y no se mueve, puede parpadear en rojo/verde todo el rato.</p><p>Antes de poner a cero el motor y usando el pulsador, manda varias veces de lado a lado la antena, con el tiempo se queda algo rigido y le cuesta.</p><p>Si ves que no va, va a tirones y no soltaste el pulsdor, se apaga el led, revisa los conectores, alguno no esta bien y tienes problemas con la alimentacion.</p><p>Si no se mueve con el pulsador, meter alimentacion externa como indica Trust1, de 13 a 18Voltios de contina (VDC).</p><p>Con 1 Amperio sobra, negativo al chasis y positivo al centro.</p><p>Suerte</p></blockquote><p></p>
[QUOTE="Tururu, post: 1075298, member: 227656"] It looks like the one I have SG2100 / FTE Dimo120+ The engine reset must be done while the engine is at 0º. The engine takes the reference and if you use usals, perfect. If it is not at 0º when resetting, part of that position as if it were zero. In the tuner configuration VU+Solo2 you have engine options, inside you have an option. Go to .... When you put on top you will see that the green box puts [B]Go to 0, press the green button. [/B] If all is well, the motor will be positioned at zero of the screen printing (reset now). If it does not move, using the button as indicated by the partner, position it to zero. When the power is ok, it turns on and green, when orders arrive by the cable (diseqc/usals commands), the LED flashes orange, if it locks and does not move, it can flash red/green all the time. Before zeroing the engine and using the button, send the antenna several times from side to side, over time it becomes somewhat stiff and costs. If you see that it is not going, it will pull and you did not release the button, the LED goes out, check the connectors, some are not well and you have problems with the power supply. If it does not move with the button, insert external power as indicated by Trust1, from 13 to 18 Volts of continuous (VDC). With 1 amp left over, negative to the chassis and positive to the center. Luck ---------- Se parece al que tengo SG2100/FTE DIMO120+ El reset al motor se tiene que hacer estando el motor a 0º. El motor toma la referencia y si usas usals, perfecto. Si no esta a 0º al hacer el reset, parte de esa posicion como si fuera cero. En la configuracion del sintonizador VU+Solo2 tienes opciones del motor, dentro tienes una opcion. Ir a .... Al ponerte encima veras que el cuadro verde pone[B][COLOR=rgb(0, 0, 0)] Ir a 0, pulsa el boton verde.[/COLOR][/B] Si todo esta bien, el motor se posicionara en el cero de la serigrafia. (reset ahora). Si no se mueve, usando el boton como indca el compañero, posicionar a cero. Cuando la alimentacion esta ok, se enciende el verde, al llegar ordenes por el cable (comandos diseqc/usals), el led parpadea en naranja, si se bloque y no se mueve, puede parpadear en rojo/verde todo el rato. Antes de poner a cero el motor y usando el pulsador, manda varias veces de lado a lado la antena, con el tiempo se queda algo rigido y le cuesta. Si ves que no va, va a tirones y no soltaste el pulsdor, se apaga el led, revisa los conectores, alguno no esta bien y tienes problemas con la alimentacion. Si no se mueve con el pulsador, meter alimentacion externa como indica Trust1, de 13 a 18Voltios de contina (VDC). Con 1 Amperio sobra, negativo al chasis y positivo al centro. Suerte [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Satellite TV receivers & systems support forums
Satellite Systems - What to Buy - What to install
New diseqc motor to replace technomate tm 2600 h-h
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top