Log in
Register
Menu
Log in
Register
Home
What's new
Latest activity
Authors
Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Current visitors
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Satellite Tv Encryption Decryption
Cards, Programmers and Cams
X-CAM, Ultra CAM, Dragon CAM, Diablo, T Rex
trex4.6 and dragon loader
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Mickha" data-source="post: 406190" data-attributes="member: 187442"><p>Does your Cas 3 have a dummy card? This is an oblong computer board, aprox 12cm by 5.5cm, which connects to your Cas 3 using the 20 pin connector, the same one the J Tag uses, smaller square board 4.5cm by 3.5cm. First download the latest CIS drivers, for me 8.1b works but others require the latest 8.2.</p><p>If it does use this to programme your Dragon Cam.</p><p>Inset your Cam into the Cas 3.</p><p>Insert the dummy board, all the way in, chip facing up.</p><p>Start your Cas 3 software, and click the Cam Module tab at the top.</p><p>Then click the Other Cams icon, and the 3rd icon, T-Rex super.</p><p>Click the little button, to the right of file name and navigate to your Predasaur.dra file. The last version is Predasaur 216, Predasaur files are for the T-Rex super modules only.</p><p>Click Start Update and wait until your Cam is loaded.</p><p>If your cam doesn't have a dummy card, or you want to use your loader card.</p><p>Start up your Cas 3 software.</p><p>Insert your loader card, chip face down, into the card slot, rear of the Cas 3.</p><p>Click the Smartcard tab, and the Dragon Card icon.</p><p>Click the Folder Icon, bottom right of the firmware bar.</p><p>Navigate to Predasaur.dra file.</p><p>Click Write to Dragon Loader Card.</p><p>Once the card is loaded, follow these instructions correctly, as a failure to do so can result in you damaging your Cam.</p><p>Tune your receiver to a FTA, Free To Air, channel.</p><p>Switch off your receiver.</p><p>Insert the loader card into your Cam, chip face up, and if not already insert your Cam into your receiver.</p><p>Navigate through your receivers menu to the Cam, and choose yes load module.</p><p>Wait until your cam is loaded, this will take a few minutes. To see the progress you can press refresh.</p><p>Once the Cam is loaded you will see a message, your cam is loaded please remove your loader card.</p><p>Remove your loader card.</p><p>Turn off your receiver.</p><p>Turn on your receiver and the Cam should be loaded.</p><p>To get Premiere you now need to activate the security update, navigate to your Cam in rthe receivers menu, enter the menu, and press Security Update, this should take a few seconds.</p><p>If you haven't already got the latest Predasaur file check out the links page, on the main forum, this will give you places where you can download them.</p></blockquote><p></p>
[QUOTE="Mickha, post: 406190, member: 187442"] Does your Cas 3 have a dummy card? This is an oblong computer board, aprox 12cm by 5.5cm, which connects to your Cas 3 using the 20 pin connector, the same one the J Tag uses, smaller square board 4.5cm by 3.5cm. First download the latest CIS drivers, for me 8.1b works but others require the latest 8.2. If it does use this to programme your Dragon Cam. Inset your Cam into the Cas 3. Insert the dummy board, all the way in, chip facing up. Start your Cas 3 software, and click the Cam Module tab at the top. Then click the Other Cams icon, and the 3rd icon, T-Rex super. Click the little button, to the right of file name and navigate to your Predasaur.dra file. The last version is Predasaur 216, Predasaur files are for the T-Rex super modules only. Click Start Update and wait until your Cam is loaded. If your cam doesn't have a dummy card, or you want to use your loader card. Start up your Cas 3 software. Insert your loader card, chip face down, into the card slot, rear of the Cas 3. Click the Smartcard tab, and the Dragon Card icon. Click the Folder Icon, bottom right of the firmware bar. Navigate to Predasaur.dra file. Click Write to Dragon Loader Card. Once the card is loaded, follow these instructions correctly, as a failure to do so can result in you damaging your Cam. Tune your receiver to a FTA, Free To Air, channel. Switch off your receiver. Insert the loader card into your Cam, chip face up, and if not already insert your Cam into your receiver. Navigate through your receivers menu to the Cam, and choose yes load module. Wait until your cam is loaded, this will take a few minutes. To see the progress you can press refresh. Once the Cam is loaded you will see a message, your cam is loaded please remove your loader card. Remove your loader card. Turn off your receiver. Turn on your receiver and the Cam should be loaded. To get Premiere you now need to activate the security update, navigate to your Cam in rthe receivers menu, enter the menu, and press Security Update, this should take a few seconds. If you haven't already got the latest Predasaur file check out the links page, on the main forum, this will give you places where you can download them. [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Satellite Tv Encryption Decryption
Cards, Programmers and Cams
X-CAM, Ultra CAM, Dragon CAM, Diablo, T Rex
trex4.6 and dragon loader
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top