big network problem with Dm 800 hd clone

[goni el]

hi i have network problem in Dm 800 hd it workt good for a month
and it stop working,
I did a network test, these where my results, I have also lost my channels

LAN Adapter
Intergrated Ethernet/ and theres a tick in the box

Local Network
connected/ and theres a tick in the box

DCHP
enable/ and theres a tick in the box

IP Address
unconfirmed/ and theres a X in the box

Namesever
unconfirmed/ and theres a X in the box
can you help me please
thank you from Goni el

 

[B16MCC]

1. Power down the Dreambox. Reboot your router, power up the Dreambox.
2. Check router settings page to see if its assigned the Dreambox an IP address.
3. See if you can access the Dreambox web interface.

 

[goni el]

i put DHCP of and i make a new ip, netmask, dns after that i restarted but still the same the iven when i hold the buton dot show me the ip
i can flash the image withaut problem with dreamup my dm 800 hd is ss75 sim 2.01 end now i flash it nabilo blackhole ss72, how can i Check router settings page to see if its assigned the Dreambox an IP address?
i trait wlan is the same no ip can you help me please

 

[goni el]

Device Information

Firmware Version
:
W300V2.0.1a_DR0_OV

MAC Address
:
00:25:12:b3:8a:7f
LAN

IP Address
:
192.168.1.1

Subnet Mask
:
255.255.255.0

DHCP Server
:
Enabled
WAN

Virtual Circuit
:


Status
:
Connected

Connection Type
:
PPPoE

IP Address
:
10.103.95.95

Subnet Mask
:
255.255.255.255

Default Gateway
:
10.103.0.1

DNS Server
:
217.24.241.206

NAT
:
Enabled

PPP connection time
:
0d:16h:37m:32s
ADSL

ADSL Firmware Version
:
FwVer:3.10.17.0_TC3085 HwVer:T14.F7_5.0

Line State
:
Showtime

Modulation
:
ADSL2 PLUS

Annex Mode
:
ANNEX_A

Downstream Upstream
SNR Margin
:
33.3 37.2 db
Line Attenuation
:
26.2 16.7 db
Data Rate
:
512 126 kbps
this shows my router idont no how to find dm800hd ip

 

[B16MCC]

Please remove this from your profile:-
My System: need keys for watching satellite

I would highly recommend you use DHCP. You are asking for trouble by not using it. If this is a clone box its likely a hardware fault.
Does the ethernet socket light come on when you plug a cable in to the Dreambox ?

 

[goni el]

yes it does

 

[goni el]

Yes it does the ethernet socket light come on when you plug a cable in to the Dreambox
i tray it with usb wlan i put my usb wlan in dm800 it fined the wireless
network but it is encrypted:no and dont connect
it says after winzart network starting FAILED on 0.0.0.0:80!
Couldn't listen on 0.0.0.0:80: (125,'Address already in use)
usb TL-WN321G
dm800hd clone sim 2.01 ss75 NabiloBlackHole V0.12.
any help

 

[packetstormer]

Device Information

Firmware Version
:
W300V2.0.1a_DR0_OV

MAC Address
:
00:25:12:b3:8a:7f
LAN

IP Address
:
192.168.1.1

Subnet Mask
:
255.255.255.0

DHCP Server
:
Enabled
WAN

Virtual Circuit
:


Status
:
Connected

Connection Type
:
PPPoE

IP Address
:
10.103.95.95

Subnet Mask
:
255.255.255.255

Default Gateway
:
10.103.0.1

DNS Server
:
217.24.241.206

NAT
:
Enabled

PPP connection time
:
0d:16h:37m:32s
ADSL

ADSL Firmware Version
:
FwVer:3.10.17.0_TC3085 HwVer:T14.F7_5.0

Line State
:
Showtime

Modulation
:
ADSL2 PLUS

Annex Mode
:
ANNEX_A

Downstream Upstream
SNR Margin
:
33.3 37.2 db
Line Attenuation
:
26.2 16.7 db
Data Rate
:
512 126 kbps
this shows my router idont no how to find dm800hd ip

Most routers have an Advanced/Status/LAN/DHCP settings page to show connected DHCP clients. What is the make of the router? Why not add a static IP address to the DM then try and connect to it from your PC/Laptop? This will rule out any DHCP problems. I have seen similar problems a few times before. There isn't any difference between a static IP address and DHCP address as long as the ISP stays the same i.e same gateway, DNS etc.

 

[goni el]

hi i fixed my problem with wlan usb and it worked
now is working but not with cable i think was a hardware problem
thank you for your help:-handclap

 

[barambulli]

hi i fixed my problem with wlan usb and it worked
now is working but not with cable i think was a hardware problem
thank you for your help:-handclap

Hi Goni, I'm having the same problem. What USB dongle are you using?

 

[goni el]

Hi Barambulli i'm using tp-link TL-WN321G dm800hd clone sim 2.01 ss75 NabiloBlackHole V0.12
and is working good

 

[barambulli]

Hi Barambulli i'm using tp-link TL-WN321G dm800hd clone sim 2.01 ss75 NabiloBlackHole V0.12
and is working good

Hi goni,

Thanks for replying.

Can you tell me what was the procedure? Did you just plug it in and it worked, or did you have to make some modifications?

Faleminderit.

 

[andrzejp129]

You need TL-WN321G v1,v2,v3. TL-WN321G v4 dont work with dm800 clone. Yes, you just plug it and it workes. I checked with maybe 10 diferent images. First time I bought v4 twice and they didnt work. Now I've got v2 and everything is perfect.