Jsc Card Questions

Status
Not open for further replies.
W

wedgy2k

Member
Messages
20
My Satellite Setup
DM500s, 80cm Dish, 6degree MonoBlock 13e/19.2e. Pli Jade Max Var
My Location
Portsmouth
Hi

I'm going to buy a JSC card for 13e for my DM500 Clone
(Nemesis 4.2)
But it has thrown up a few questions, I hope some one could answer please.

Will CCcam pick up the card?
Once the card hase been activated and the timer is countingdown
Can i reflash to another image and it still work?

Cheers

Wedgy2k
 
H

HB13DISH

Retired Mod
Messages
3,764
My Location
Middle East - Israel
wedgy2k said:
Hi

I'm going to buy a JSC card for 13e for my DM500 Clone
(Nemesis 4.2)
But it has thrown up a few questions, I hope some one could answer please.

Will CCcam pick up the card?
Once the card hase been activated and the timer is countingdown
Can i reflash to another image and it still work?

Cheers

Wedgy2k
I never had this specific card, but the card reader in the Dreambox 7000S did open other official smartcards with CCcam or Mgcamd
The card activation has nothing to do with the image.
You can take it out and insert it in any other receiver that would support the card encryption (based or other cards experience).
 
M

moridark_back1

Regular Member
Messages
129
My Satellite Setup
DM500 &DM88HD & humax5400z&
zone2 & 1.5m dish
My Location
oxfordshire
the answer is yes to both Questions
 
W

wedgy2k

Member
Messages
20
My Satellite Setup
DM500s, 80cm Dish, 6degree MonoBlock 13e/19.2e. Pli Jade Max Var
My Location
Portsmouth
HB13DISH said:
I never had this specific card, but the card reader in the Dreambox 7000S did open other official smartcards with CCcam or Mgcamd
The card activation has nothing to do with the image.
You can take it out and insert it in any other receiver that would support the card encryption (based or other cards experience).
Hi Thanks for the answer
When i mailed the vendor asking if this card would work in my Dm500
here's the response
"
Most of our customer who bough this card to use on their Dreambox did not work as most of their system is only Irdeto enabled.
If you check your manual if your receiver has got a viaccess 3.0 enable if not then you will need a viaccess cam if you have a ci/cam slot.
"
Seems a bit over the top?

So has anyone got a JSC card in their dm500 slot?

Cheers

Wedgy2k
 
H

HB13DISH

Retired Mod
Messages
3,764
My Location
Middle East - Israel
wedgy2k said:
Hi Thanks for the answer
When i mailed the vendor asking if this card would work in my Dm500
here's the response
"
Most of our customer who bough this card to use on their Dreambox did not work as most of their system is only Irdeto enabled.
If you check your manual if your receiver has got a viaccess 3.0 enable if not then you will need a viaccess cam if you have a ci/cam slot.
"
Seems a bit over the top?

So has anyone got a JSC card in their dm500 slot?

Cheers

Wedgy2k
Looks like they are not familiar with this receiver, as it has only a card reader and NOT a CI CAM slot. Don't bother about their reply, it just shows ignorance.
You will need an emulator like CCcam. As I mentioned before I don't have this card so buy at your own risk.
Have you installed CCcam on your present image?
Do you have any other official smartcards to test if it will open any of the channels in the package?
 
W

wedgy2k

Member
Messages
20
My Satellite Setup
DM500s, 80cm Dish, 6degree MonoBlock 13e/19.2e. Pli Jade Max Var
My Location
Portsmouth
HB13DISH said:
Looks like they are not familiar with this receiver, as it has only a card reader and NOT a CI CAM slot. Don't bother about their reply, it just shows ignorance.
You will need an emulator like CCcam. As I mentioned before I don't have this card so buy at your own risk.
Have you installed CCcam on your present image?
Do you have any other official smartcards to test if it will open any of the channels in the package?
Thanks HB

I do have CCcam 2.0.11 installed, but no i'dont have any smartcards to test.
I'll buy it and have a go :) Whats the worst that can happen? is it won't work. LOL

If it doesn't want to play, I suppose is could always try and share it from my PC.
Mmmmmmmmm I need a new project..............
I'd never herd of dreambox a year ago and have really enjoyed getting it going.
So Q, forum searching, 100 card reader/ CS /CCcam questions LOL

Cheers

Wedgy2k
 
W

wedgy2k

Member
Messages
20
My Satellite Setup
DM500s, 80cm Dish, 6degree MonoBlock 13e/19.2e. Pli Jade Max Var
My Location
Portsmouth
Ordered
LOL
 
H

HB13DISH

Retired Mod
Messages
3,764
My Location
Middle East - Israel
wedgy2k said:
Ordered
LOL
Good luck. :)
I have a feeling that it will work without any problem.
 
W

wedgy2k

Member
Messages
20
My Satellite Setup
DM500s, 80cm Dish, 6degree MonoBlock 13e/19.2e. Pli Jade Max Var
My Location
Portsmouth
Got it and it worked 1st go LOL
Worried for nothing

Cheers
 
H

HB13DISH

Retired Mod
Messages
3,764
My Location
Middle East - Israel
wedgy2k said:
Got it and it worked 1st go LOL
Worried for nothing

Cheers
Good. Enjoy. :)
 
M

moridark_back1

Regular Member
Messages
129
My Satellite Setup
DM500 &DM88HD & humax5400z&
zone2 & 1.5m dish
My Location
oxfordshire
you didnt have to worry i told you it will work couse i have one works with cccam and gbox
 
W

wedgy2k

Member
Messages
20
My Satellite Setup
DM500s, 80cm Dish, 6degree MonoBlock 13e/19.2e. Pli Jade Max Var
My Location
Portsmouth
Slight issue :-(
when looking at CCcaminfo web page

card reader /dev/sci0
handled 17(17) ecms and 2(0) emms
Viaccess card
Caid 500
Cardserial bexxxx
ident fff920 - bexxxx
ident 30700 - bexxx
valid from 16-1-2009 untill 25-4-2009

So i mailed the vendor asking why "valid from 16-1-2009 untill 25-4-2009"
as i paid for 12month sub

Here's the response i recieved
"if you don't use an original red viaccess cam or box for Art Or Al-Jaz cards it wont upgrade the card to the full subscription.
Kind regards Xxxxx"

So i guess i have to find a friend with a viaccess cam?

Cheers
Wedgy2k
 
H

HB13DISH

Retired Mod
Messages
3,764
My Location
Middle East - Israel
wedgy2k said:
Slight issue :-(
when looking at CCcaminfo web page

card reader /dev/sci0
handled 17(17) ecms and 2(0) emms
Viaccess card
Caid 500
Cardserial bexxxx
ident fff920 - bexxxx
ident 30700 - bexxx
valid from 16-1-2009 untill 25-4-2009

So i mailed the vendor asking why "valid from 16-1-2009 untill 25-4-2009"
as i paid for 12month sub

Here's the response i recieved
"if you don't use an original red viaccess cam or box for Art Or Al-Jaz cards it wont upgrade the card to the full subscription.
Kind regards Xxxxx"

So i guess i have to find a friend with a viaccess cam?

Cheers
Wedgy2k
That's new! :confused
Hope that they are not lying and just sent you a ~ 3 months valid card.
I am sure that many members would volunteer to help you. Sorry I am not in the UK, otherwise I would be happy to assist.
Suggest to make a new post and ask if any member had a similar problem with their official cards subscription period.
Also try other CAMs like MgCamd or SCAM and see if they can update the finish date.
 
H

hamad99

Member
Messages
4
My Satellite Setup
DB500S
My Location
KSA
hello,
how to see the CCcaminfo web page?? i have dreambox 500s
i have JSC card which didn't work and i want to see this page CCcaminfo web page!!!
thanks in advance ..
 
H

HB13DISH

Retired Mod
Messages
3,764
My Location
Middle East - Israel
hamad99 said:
hello,
how to see the CCcaminfo web page?? i have dreambox 500s
i have JSC card which didn't work and i want to see this page CCcaminfo web page!!!
thanks in advance ..
In a windows browser, type
_http://dreamboxIP:16001
Look for Entitlements
(You have to shutdown the box first, insert the card with chip face down, switch on)
 
A

A nonymous

Member
Messages
3,586
You can update the Viaccess cards using NewCS and MGCamd apparently :confused

This guide was originally posted by Ramad on EuroCS forum.


In this small ''How to'', I will try to share my experience of updating a TV-card based on Viaccess 3.0 using my DM600PVR Dreambox.

By updating a Viaccess card I mean updating the subscription period, for example, my card is a JSC Sport+ based on Viaccess 3.0 with 1 year subscription period, I started using the card on 16/5/2008 at that time it gave me subscription rights to 23/8/2008...the card stopped working after that, enabling EMM on CCcam did not update the card neither leaving the card in another receiver for several days did update the subscription rights.

The reason for me writing this small ''How to'' is that I could not find any information on how to update a Viaccess card anywhere on ECS forum or the internet, there is however a small post by our Mod Smurfer where he wrote that he uses Mgcamd to update his Viaccess card, but unfortunately, he did not give any information of how to do that.

So, if you have a Viaccess card that you need to be updated, here is how to do that using your Dreambox...

For this I used NewCS 1.61 and Mgcamd 1.3d on PLI-image, NewCS 1.62 can be downloaded and installed on PLI but it will not show as server, it's why I used NewCS 1.61...DCC 2.95 is used for configuration/editing the configuration files.


1. Installing NewCS 1.61 and Mgcamd 1.3d



A. Press the Blue-button on your remote, and choose Software Mangement

B. Choose Download latest menu from the menu, choose Yes and then press the Red-button on your remote to close the window.

C. Choose Downloads from the menu then choose SoftCams/Cardservers from the menu.

D. Choose and press OK on Mgcamd (1.3d) to download, press the Red-button to close the installation window and return to the SoftCams/Cardservers when the installation is done, repeat the same with Mgcamd config (1.3d) to download and install the Mgcamd configuration file.

E. On the SoftCams/Cardservers, brows down to Older Softcams and then choose NewCS cardserver, press OK to download and install the NewCS Cardserver (1.61)

2. Configuring NewCS 1.61 and Mgcamd 1.3d

A. Run DCC 2.95, choose the FTP tab and brows to the folder /etc/tuxbox, if you have a Gemini-image or a Nabilo-image then it's located in /etc/tuxbox/config, right-click the file newcs.xml and choose Edit from the menu.
When the file opens, clear all the text inside of it and copy these line from here and paste them in the newcs.xml file:

Code:
<newCSconfig>
<readers name="SCI">
<device>
<name>Lower Cardreader</name>
<type>sci</type>
<mhz>357</mhz>
<node>/dev/sci0</node>
<parity>odd</parity>
<reset>normal</reset>
<export>Yes</export>
<enabled>Yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>


<irdeto-camkey>0000000000000000</irdeto-camkey>
<irdeto-camkey-data>000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000</irdeto-camkey-data>
<crypto-special>No</crypto-special>
<ipk>000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000</ipk>
<ucpk>00000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 000000000000</ucpk>
<PTShandshake>No</PTShandshake>
<carddetect>yes</carddetect>
<newcamd_port>34000</newcamd_port>
<autosid>Yes</autosid>
<Seca-PPV>no</Seca-PPV>
<pincode>0000</pincode>
<priority>round</priority>
</device>
</readers>
<cache>
<emm>20</emm>
<ecm>-1</ecm>
</cache>
<debug>
<password>NewCSpwd</password>
<level>normal</level>
<type>init</type>
<output>console,tcp</output>
<console_options>normal,init</console_options>
<tcp_port>1001</tcp_port>
<tcp_options>normal,init</tcp_options>
</debug>
<newcamdserver>
<enabled>Yes</enabled>
<name>newcs</name>
<server-ip>Your_DNS_Host_Name</server-ip>
<deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey>
<user>
<name>Your_Dreambox_User_name</name>
<password>Your_Dreambox_Pass</password>
<hostname>Your_Dreambox_Lan_IP</hostname>
<port>34000</port>
<au>on</au>
<sidoverride>on</sidoverride>
<spider>No</spider>
<allow>lower</allow>
<rate>2</rate>
</user>
</newcamdserver>
<httpd>

<server>
<port>8080</port>
<enabled>yes</enabled>
</server>
<user>
<name>Your_Admin_User_Name</name>
<password>Your_Admin_Pass</password>
<accesslevel>admin</accesslevel>
</user>

</httpd>
</newCSconfig>
The lines in Red are to be changed to your own parameters such as your Dreambox Lan-IP, User-names, Passwords...etc.

When done, choose Save and Exit to exit the editor.


B. Brows to the file newcam.list in /usr/keys , right-click the file and choose to edit, when the file opens, you will see these to lines:

Code:
CWS = 127.0.0.0 10000 local local 01 02 03 04 05 06 07 08 09 10 11 12 13 14 wan cardserver
CWS = 127.0.0.1 10001 local local 01 02 03 04 05 06 07 08 09 10 11 12 13 14 wan cardserver
Change the first line to:

Code:
CWS = [COLOR="Red"]Your_Dreambox_Lan_IP[/COLOR] [COLOR="RoyalBlue"]34000 [/COLOR][COLOR="Red"]Your_Dream_User_Name[/COLOR] [COLOR="Blue"]Your_Dreambox_Pass[/COLOR] 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan cardserver
Again, the parameters in Red and Blue are to be changed to your own parameters such as your Dreambox Lan-IP, user-name, password...etc,and you must keep the spaces as they are, parameters that have to be changed are the same as in the newcs.xml

Choose Save and Exit to exit the editor when done.

3. Starting NewCS+Mgcamd


A. Press the Blue button on your Dreambox remote, move to Softcamd Setup and press OK, choose NewCS as Cardserver and choose Mgcamd as Default SoftCam, press the Red button to start the NewCS Server and press the Green button to Save and Restart the Mgcamd emulator.

B. Put your card in your Dreambox and change the channel in your Dreambox to one of your card providers channels, if you have configured NewCS and Mgcamd correctly then it will only take a few seconds for the picture to appear which means that the update is complete.

You can check if your card has been updated by writing your Dreambox Lan-IP followed by port 8080, means, if your Dreambox has the Lan-IP ( example ): 192.168.1.5 then you need to write: 192.168.1.5:8080 in your browser and hit Enter...
Enter the username and the password that you have created in the <httpd> lines in your newcs.xml configuration file to log in to the server.

The subscription period can be shown by clicking on Entitlements and then clicking on List to download the Entitlements informations, such as subscription period.

The only difference between PLI image, Gemini and Nabilo images is that Gemini and Nabilo offers the combination of Mgcamd+NewCS as a single download, everything else is the same.

I hope that this small ''How to'' can be helpful for them that have trouble updating there cards.



Hopefully you may find this of use. I haven't tested it so i take no responsibility if it doesn't work or if it causes your box to self destruct after 15 seconds :-lmao
:-beer

Nano
 
S

Sharkadder

Regular Member
Messages
440
My Satellite Setup
Dreambox 8000 HD PVR+DVD, 80cm Dish, 1.2 Compatible Motor, Quad LNB, Samsung 22&quot; 1080p HD TV/monitor, Yamaha RX-V765 Amplifier, Tannoy Mercury FC Centre Speaker, 2 x Tannoy F1 Custom Speakers, 2 x Tannoy FR Custom Speakers, EPOS ELS Sub Woofer
My Location
Teesside (North East England)
sounds good, i shall look into that at some time. I wondered why my card never updated since then, i just presumed that it was because i never left the channel on overnight.

I will download MGcamD and NewCS tomorrow, update my card and then put CCcam back on once it has updated. It should be fine again for another 3 months after that i think.

Anyways, thanks for that solution (y)
 
K

kokar69

Member
Messages
2
My Satellite Setup
Dreambox 7000S with image Gemini 4.7
My Location
Sweden
Hi

I followd what you wrote and get this, is it working? No picture is showing on screen!
What can be failure?

Entitlements for card 0
.-------------------------------------------------.
| Provider | Channel ID | From | To |
|----------|------------|------------|------------|
| 00 | EFFE | 0x0E71 | 0x0E71 |
| 00 | EFFD | 0x0E71 | 0x0E78 |
| 00 | 006F | 0x0E71 | 0x0E78 |
| 00 | 0004 | 0x12C1 | 0x13BF |
| 00 | 0009 | 0x12C0 | 0x139E |
| 00 | 7FFD | 0x12C0 | 0x12CA |
| 00 | 7FFE | 0x11C0 | 0x11DE |
| 00 | FFD8 | 0x11C1 | 0x11CB |

Regards
koakr
 
Topper

Topper

Amo Amas Amant Admin
Staff member
Messages
22,894
My Satellite Setup
IDD CI24 ECONO MM Penta 1.20 Galaxy II
1.2Mtr Polar MTG yes it has been on the arc for 25 years and is now fixed on 13 East using two pairs of rusty molegrips. Unlike me they never groan but always perform.
My Location
Blackburn, Lancashire
You are posting on a thread that is 7 years old..... encryption systems evolve on a daily basis, I think we will put this one to bed
 
Status
Not open for further replies.
Top