Log in
Register
Menu
Log in
Register
Home
What's new
Latest activity
Authors
Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Current visitors
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Linux Based Receivers
Dreambox Support Forum
Dreambox Satellite Receiver | Tutorials | Software
Dreambox 500
Loading image to flybox 500s A little help requested
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="RichardinSpain" data-source="post: 779443" data-attributes="member: 310811"><p>There are 3 main programes that you need</p><p>1,Dream box control centre (DCC) this is a ftp programe which enables you to transfer files into the db..i.e keys,sat lists plugins etc, once logged in to your db you can see the linux files (via ethernet) </p><p>2,Flash Wizard Pro, this is the prog i used to flash the image, make backups etc (via ethernet)</p><p>3,Dreamup, in case you flashed a bad image or something went wrong during the flash and your box wont boot..(through rs232, MUST be null modem cable)</p><p></p><p>Ok to get started you need to know the ip of your db, hopefully you can navigate round your menus in the db to find this. Look under network settings or something like that...load up flash wizard pro, click on 'configuration and utilities tab' here you will see where to enter you db's ip..Enter ip address and if applicable login and password..if it doesnt need a password leave blank..sometimes login = root..Then click on 'instal a firmware into flash memory' click on the open folder symbol and find your new image on you pc (hopefully youve already downloaded one, pli jade etc) then it should be self explanatory from here..I always made sure the 'kill enigma' box was checked..After its loaded the box should reboot, if not just turn it off and switch back on again..If the flash has worked ok it will take you through the setup of configuring your sats etc..Obviously being that a new image has been loaded it would have lost all your previous settings etc but after you have set it up you can make backups of what you have done. Hope you get on ok</p></blockquote><p></p>
[QUOTE="RichardinSpain, post: 779443, member: 310811"] There are 3 main programes that you need 1,Dream box control centre (DCC) this is a ftp programe which enables you to transfer files into the db..i.e keys,sat lists plugins etc, once logged in to your db you can see the linux files (via ethernet) 2,Flash Wizard Pro, this is the prog i used to flash the image, make backups etc (via ethernet) 3,Dreamup, in case you flashed a bad image or something went wrong during the flash and your box wont boot..(through rs232, MUST be null modem cable) Ok to get started you need to know the ip of your db, hopefully you can navigate round your menus in the db to find this. Look under network settings or something like that...load up flash wizard pro, click on 'configuration and utilities tab' here you will see where to enter you db's ip..Enter ip address and if applicable login and password..if it doesnt need a password leave blank..sometimes login = root..Then click on 'instal a firmware into flash memory' click on the open folder symbol and find your new image on you pc (hopefully youve already downloaded one, pli jade etc) then it should be self explanatory from here..I always made sure the 'kill enigma' box was checked..After its loaded the box should reboot, if not just turn it off and switch back on again..If the flash has worked ok it will take you through the setup of configuring your sats etc..Obviously being that a new image has been loaded it would have lost all your previous settings etc but after you have set it up you can make backups of what you have done. Hope you get on ok [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Linux Based Receivers
Dreambox Support Forum
Dreambox Satellite Receiver | Tutorials | Software
Dreambox 500
Loading image to flybox 500s A little help requested
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top