Magic Modul continued .....

P

pmcmill

Guest
Hi All,
I tried adding to the previous thread twice today buy my posts don't show up . Hopefully I've not been banned already !!
Anyway , I was about to buy an Irdeto 5 in 1 CAM today when I came across this Magic thingy . Simple question really , would I be better off spending a little more and buying this CAM . I'm interested in Seca/Seca2 and Nagravision .
Thanks in advance.
Paul
 
rolfw

rolfw

Believe it when I see it Admin.
Staff member
Joined
May 1, 1999
Messages
38,295
Reaction score
1,620
Points
113
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
Must be down to local caching Paul, they seem to have found thir way on to my screen.

rolf
 
P

pmcmill

Guest
It's weird rolfw . I've cleaned out all my temp files etc. but I can still only see the post from verywiseguy . I'll try rebooting .
Paul
 
P

pmcmill

Guest
Hi Rolfw,
Still get the same problem and I´m using another PC . Oh , well not to worry . Hopefully someone will post back with some info .
Thanks
Paul
 
rolfw

rolfw

Believe it when I see it Admin.
Staff member
Joined
May 1, 1999
Messages
38,295
Reaction score
1,620
Points
113
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
Could be the cache at your ISP playing up, I've had similar problems on occasions, although not with this site.

Rolf
 
P

pmcmill

Guest
Hi Again,
During my digging around I found this abut programming my MM .

How to do:

1. put the module in SetTopBox (ST:cool:
STB-CI-Menue: DreamLoad (ready for upload) or:
select "Prepare for loading" and press OK
"YES - Activate loader" and press OK
(now: the old file in the module is deleted)
remove and re-insert the module
Now the module is in upload-mode


2. insert programmer into the module
(green LED = power), connect RS232-cable to PC comport 1 or 2


3. start loader-programm
select comport in menue "Settings"
press connect


4. load file *.mbf by clicking "Program module ..."
select file
upload begin


5. remove and re-insert the module

Does this mean I need a STB to fully program this device or can I just start from point 2 ??

Thanks

Paul
 
rolfw

rolfw

Believe it when I see it Admin.
Staff member
Joined
May 1, 1999
Messages
38,295
Reaction score
1,620
Points
113
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
Yes Paul, as the receiver powers the CAM I would guess that you will need to use step one as well.

rolf
 
P

pmcmill

Guest
Thanks rolfw ,
Is this STB a seperate box or is my Strong 4375 a STB ??
Paul
 
rolfw

rolfw

Believe it when I see it Admin.
Staff member
Joined
May 1, 1999
Messages
38,295
Reaction score
1,620
Points
113
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
Yes, providing it has a CI slot

Rolf
 
Top