matrix 2 up date

nitefire

Regular Member
Messages
93
Likes
1
My Satellite Setup
1M Dish TD110 Diseqc USALS Twin LNB Tecnomate TM-5302HD
Pair of T&K brackets
My Location
Grays,Essex
#1
Technomate 500cipluse I brought a infinity phoenix usb with 2 funcard6, to up date my cam from
1.055 to 1.070 but have no luck from doing this.
Do any one know of any shops who can do this for me.

Thanks
 

rolfw

Believe it when I see it Admin.
Staff member
Messages
37,671
Likes
1,279
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
#2
Have you looked at the sticky at the top of this section Nitefire? The process is quite straightforward, where do you think it is going wrong?
 

nitefire

Regular Member
Messages
93
Likes
1
My Satellite Setup
1M Dish TD110 Diseqc USALS Twin LNB Tecnomate TM-5302HD
Pair of T&K brackets
My Location
Grays,Essex
#3
Ok downloaded file 1.070 unzip the file, open it up there's 7 files this is where it get's me
confused on the usb it says PIC EXTand runing XP
 

rolfw

Believe it when I see it Admin.
Staff member
Messages
37,671
Likes
1,279
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
#4
Only three of the files are relevant to you, the upd file which goes in the flash on both cards and the two 1024 HEX files which go in External EEPROM.

I believe that the setting is Prussian card 4 for your funcards.
 

nitefire

Regular Member
Messages
93
Likes
1
My Satellite Setup
1M Dish TD110 Diseqc USALS Twin LNB Tecnomate TM-5302HD
Pair of T&K brackets
My Location
Grays,Essex
#5
Hi rolfw Thanks for trying this but I followed every thing that you said, I get insert card1
when I do that opening card then performing serial download then it says cable romved or baudrate too high for this stb what does this mean
 

rolfw

Believe it when I see it Admin.
Staff member
Messages
37,671
Likes
1,279
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
#6
Sorry Nitfire, think i gave you a bum steer there, you need also the loader hex, not the upd file, Try using the Toeloader file, you can find it here.
 

nitefire

Regular Member
Messages
93
Likes
1
My Satellite Setup
1M Dish TD110 Diseqc USALS Twin LNB Tecnomate TM-5302HD
Pair of T&K brackets
My Location
Grays,Essex
#7
No same old problem I have tried it on Tequela 2 (30w) and BBC1 (28.5)
Just as it says in last post.
 

Norm

Specialist Contributor
Messages
259
Likes
4
Location
Aberdeen
My Satellite Setup
Channel Master 1.2m motorised, V Box, Technomate TM-5402HD.
My Location
Aberdeen, Scotland
#8
Nitefire, I sympathise with you over your problem. I also have struggled upgrading the MR with Fun6s. It seems like I have read every post on every board, tried every proposed solution but still with no absolute success. I have managed to upgrade the MR in my BEC receiver to versions 1.06 and 1.07t so I now know that I have the procedure correct but I have still failed with 1.07. This isn't a problem because 1.07t works fine for me. I know from all the posts I've read that others have had our type of problem with Technomate receivers.

I had convinced myself that letting the CAM cool down for a few hours before upgrading did the trick (worked for 1.06 and 1.07t but not for 1.07). I have also found that inserting the Fun6s into the MR, not hitting OK command but letting the CAM eventually default to download improves the chances (my successes have all been achieved that way). You could try these and see what happens. Also don't forget to disconnect the LNB from the receiver for absolute certainty of a FTA channel.

Over the weekend, I spent hours trying to program a tit card - unsuccessfully. Again I tried every tip that I could find. Eventually I was sure that the only explanation for my failure was that my Infinity progger must be faulty. In order to prove this, I loaded the Infinity software into my son's PC and, literally in five minutes, I had a working tit card. My PC is on XP and my boy's on W2K. I'm just using this to illustrate that sometimes there doesn't appear to be a rational explanation why things don't work, when they do it seems so easy and when they don't it's mighty frustrating. Especially when you're following the procedure to the letter! Maybe the problems are down to Microsoft?

All I can say is stick with it, eventually you might hit the winning combination. Alternatively you could buy a load of raffle tickets and hope you win the CAS2 programmer.

Norm.
 

rolfw

Believe it when I see it Admin.
Staff member
Messages
37,671
Likes
1,279
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
#9
I like the raffle ticket idea Norm. :)

Even if you don't win the CAS2, but perhaps one of the others, you may be able to swap with another winner. :)

@ Nitfire. Try starting the receiver on a FTA channel, with CAM inserted and no LNB connection, some people found that this worked.
 
Top