Matrix Cam (Still not Working)

freebird

Regular Member
Messages
16
Likes
0
My Location
Loughborough Leicestershire
#1
Help Needed,
Loaded the Flash Hex into the Multiprog Flash Memory
Then Loaded The SXFun 6in1 Ext Eeprom.
Programmed the card and inserted it into the CAM when asked.
I then get the following message;
Cable removed or Baudrate too high for this STB
PLEASE TRY AGAIN.
Can anyone tell me where I am going wrong.
Phil
 

johnbruce

Regular Member
Messages
22
Likes
0
#2
hi freebird try putting your card in the otherway up
i think that this is what the problem is
and you might get where it says invalid card but keep trying it will work eventualy
hope this helps
JB
 

freebird

Regular Member
Messages
16
Likes
0
My Location
Loughborough Leicestershire
#3
Hi; Johnbruce,

Tried the card both ways.
Keep getting invalid card please remove
Also the other way Cable removed or
Baudrate too high for this STB
please try again.
 

rolfw

Believe it when I see it Admin.
Staff member
Messages
37,699
Likes
1,287
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
#4
Can't quite work out what you are trying to do here freebird, if you are trying to load the Matrix Reloaded, what software version are you using and on which type of card?
 

freebird

Regular Member
Messages
16
Likes
0
My Location
Loughborough Leicestershire
#5
Hi Rolfw,

Using Funcard 6 and MR1(1).081upd
UCAS V3.0 version 1.7.12.2.1
There are no keys and no access to (set default key) in
the CAM menu.
Do I need to programme this in before downloading
the update.
Getting the cable/baudrate or wrong card message
It did accept the card once and downloaded it but asked
for a second card to be inserted.
 

rolfw

Believe it when I see it Admin.
Staff member
Messages
37,699
Likes
1,287
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
#6
The file for 1.081 Fun6 version) should have three parts, a loader flash and two eeprom files. http://67.43.4.157/~toe/showthread.php?t=78486 look for the fun 6 file, you load the loader and first file on and put in CAM, then when it asks for the second card, you load the loader and second Eeprom file and re-insert the card.
 

freebird

Regular Member
Messages
16
Likes
0
My Location
Loughborough Leicestershire
#7
Thanks Rolfw:

Got the software into the cam,it now reads 1.081.
Now I have got to work out how to update the keys.
 

rolfw

Believe it when I see it Admin.
Staff member
Messages
37,699
Likes
1,287
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
#8
You can do that manually in the CAM menu, then when you've done, you press, set default key and the new keys should be loaded. :)
 

russquk

Regular Member
Messages
94
Likes
0
#9
from what i know you get that baudrate message when the loader is missing or wrong incase anyone else gets it,the first time i programmed the MR i rushed and didnt really read what to do i hadnt even put the loader file on the card!!
 
Top