Multivision

Status
Not open for further replies.
M

MH29

Member
I changed my receiver over the weekend of 14/15 and for some reason Im unable to unscramble Multivision 1, 2 & 3. I can decode all the usual others with my 6-in-1 card via a magic cam.

I switched from a Manhatten 6900 to a Technomate 5500 CI. I had my Card updated today (22.06.03) and im still having the same problem ?!?!?!

Help would be greatly appreciated.
 
MH29 said:
I changed my receiver over the weekend of 14/15 and for some reason Im unable to unscramble Multivision 1, 2 & 3. I can decode all the usual others with my 6-in-1 card via a magic cam.

I switched from a Manhatten 6900 to a Technomate 5500 CI. I had my Card updated today (22.06.03) and im still having the same problem ?!?!?!

Help would be greatly appreciated.
Click to expand...

If you are still having problems try the latest DaveM files from
Phillsfiles.

They worked for me also with a Technomate 5500 CI.

Meldrew
 
Power down the receiver and power it up again. On my BEC receiver after power up, if I first view an MV channel when it is FTA (ie promo), it will never open subsequently. This always happens and I can demonstrate it 100%. But don't ask for an explanation why!
 
i also want the codes for multivision
lamalove#gmail.com #=@
thanks
 
abdoukhaled said:
I need ur help to watch multivision channels.I have humax receiver without cam or card plz thanks
Click to expand...

You may get a better response posting in the "Humax" section abdoukhaled. However, you will need a cam to receive any of the encrypted channels. Xcam would be a good start.

Regards - Marts
 
if same channels were scrambled on both decoder should i manualy install the codes of multivision on both decoders?
 
steph007 said:
if same channels were scrambled on both decoder should i manualy install the codes of multivision on both decoders?
Click to expand...


guys what is wrong with you :)

if you do small serch in the forum you will find many code finder.

and after finding the code finder if you dont know how to enter it.?

tell me the reciver model no, then i will tell you how to enter the codes,
you have to decode it every day becuse the codes are changing every day now.
 
korouk this is an old post m8 if they hav,nt sorted it out now they never will
:-DOH! :-rofl2 :-DOH!
 
hello there ! i just try to turn on this channels but it's don'e open , if there a way to show it please help me , my satteltie reciever is StarCom x-130D plus
 
Hi
Could you please send me the Codes for the multivison because my memory of the DVB is low and I can't find a software for it, my mail is ac_acac*yahoo.com.

Thanks
 
No-one is going to send you anything my friend. Even if they did, the codes would be out of date by the time you installed them.

Lets get this straight for everybody - MV & TPS codes are changing every 30 minutes or so.
 
I Received Them Free , And At Last Time They Changed Code, So If You Write New Code /viaccess/ I Can Change It And See These Channels
 
shomud said:
can u please send me a code finder
at shomud*yahoo.com
Click to expand...

Nobody will send you anything that is not hwo a forum works, all the information is here it is up to you to go look for what you want to find out
 
Hi!!I want codes for Multivision and Spice Platinum.If any one has please send the latest one on pluse_1974*yahoo.co.in
 
Ok folks - lets clear this up. No-one will send anyone anything. This is a self help forum - you want something - you go and find it - folks on the forum will give you suggestions as to where stuff can be found.


There arent any codes for SP & MV - either do without or pay for the service. (The codes are changing every 30 minutes or so.)
 
Status
Not open for further replies.
Back
Top