Please help! Idiots guide needed

M

mat_d

Member
Messages
3
Likes
0
#1
Hi need some help please. If I buy a tit card and programmer do I program it just like I did with the old s**a 1 cards? Is it just a case of finding the right hex and eeprom files or do I have to put some software to the card first like a loader or something. Also will a Ast 1.3 be any good with the tit? Sry, bit new to all this S**a 2 business.

Many thanks :)
 
Razor

Razor

Retired Mod
Messages
1,319
Likes
0
My Location
Ireland
#2
Tit cards come with their own software ( or opperating system, OS for short ). All you need is a programmer that will work in PHOENIX mode and the correct hex and eeprom files.

It sounds easy, and is if you do some reading first, but look at the Tit section on any board and you will see guys who did no reading up , pulling their hair out.
 
H

H.GEE

Regular Member
Messages
26
Likes
0
#3
As Razor says, you need to read up on other boards [Sadudez] and the relevant 'How To' stickys and then one of the procedures for programming a tit card will be as folows..........Start with titanium cardprogger 1[1][1].10.02..erase titcard and show OS 106...open file named TitaniumS2CardSoft v18n rev1..or later updated file by aston ......load hex and eep into card and burn in the usual way ...card is now programmed with hex and eep [v18n rev1]...leave card in phoenix programmer...close titanium cardprogger 1[1][1].10.02.. open Seca2Editor v 1.9n Aston that comes with the file v18rev1... press unlock card ... click open s2key file on editor ..open file Seca2keysAU ..select and open Seca2keyAU SPdat. and the editor is loaded..you will see the keys change in the editor..click on editor 'write keys to card'.....finished ..remove card and insert in mr110 cam..............hope this may be of some help. , although seca is no longer available the above file etc will be useful to do a practice run to get the hang of it . Conax can be done and is available at present so look in the appropiate file section on satdudez.
technomate5000ci infinity usb phoenix mr1.10 bluetit
 
Llew

Llew

cerca trova...
Staff member
Messages
14,536
Likes
3,436
My Satellite Setup
Triple Dragon, Dreambox 8000, Echostar AD3000ip, TBS6522,6925,6983 PCie cards.
Gibertini 1.25m motorised dish driven by the AD3000, with either Inverto BU Quad or Norsat / XMW Ka LNBs . SMW 1.05m + 3 other dishes. Speccy: Promax HD Ranger+
My Location
The Flatlands of East Anglia
#4
@mat d
Also will Ast 1.3 be any good with the tit?
Yes, works OK with Aston 1.03/1.05

Llew
 
B

Burnham Beech

Specialist Contributor
Messages
1,016
Likes
41
#5
Some excellent advice above.

But remember that whatever you do you won't be able to get anything with a Titanium card and an Aston103 cam at present.

Whether it might change in the future...............................................................................................................................nobody knows.
 
M

mat_d

Member
Messages
3
Likes
0
#6
Hi, Thanks for your time and help guys. Guess I'll have invest in a m/r cam too then. Or will an ice cam be any good as I have one of them too.

Thanks again!
 
BGonaSTICK

BGonaSTICK

Retired Moderator
Messages
5,145
Likes
0
My Satellite Setup
Dreambox 7000, Skystar2
My Location
Brighton
#7
As BB says, no SΣCA2 ATM, and may never be again, so If that's the main thing you're after, I'd invest your money elsewhere until it's back :)
 
Top