RAI1 etc TPs missing

hairybadger

hairybadger

Bricoleur
My Satellite Setup
see sig
My Location
near Geneva, Haute-Savoie, France
I've been watching games that aren't available FTV on the French channels on RAI 1 11776V using a valid Tivusat card. The TP is showing very ropey signal at the moment - in fact a rescan didn't pick it up the TP at all. RAI 5 11013H comes through fine. I guess I'm connected to a multiswitch - 13E is on DiSEqC A, 19.2E on B. The weather is a bit dodgy but I haven't had problems with it before.

Hmmm with blindscan I've got it back on 12614V, but the rain margin is zero (raining at the moment, strength is 51% and it's breaking up occasionally). This TP isn't listed on Lyngsat. RAI News 24 on 11011H (listed as 11013 on Lyngsat) is at 69%.

No, I don't have access to the roof or the multiswitch :N.
 
RAI 1 HD is listed as 11766 V 29900 DVB-S2 8PSK 3/4 but the SD version, is on 10992 V 27500, can you get the SD version?
I use kingofsat, to search for individual channels.
 
Mickha said:
RAI 1 HD is listed as 11766 V 29900 DVB-S2 8PSK 3/4 but the SD version, is on 10992 V 27500, can you get the SD version?
I use kingofsat, to search for individual channels.
Click to expand...
I'm not getting anything on 11776V now, nor 10992V. Odd.
 
changing the LOF does not affect the quality, since the box uses AFC (it is only relevant for transponders with a very low SR)
can you post a picture of the result of blindscan 11700-12700V here?
 
EnoSat said:
changing the LOF does not affect the quality, since the box uses AFC (it is only relevant for transponders with a very low SR)
can you post a picture of the result of blindscan 11700-12700V here?
Click to expand...
OK, something weird going on. Little in this scan is in the right place. 19.2E appears to be OK, though - Al Jazeera English is on the "correct" TP.

However: Museum UHD *is* 10725H (near enough what Lyngsat has), plenty of Kabelio on 11096H.

Solo2, OpenVix more-or-less up-to-date.
I have one input connected, 13E and 19.2E are on it. Both set as Universal LNB.
13E - DiSEqC 1.0, port A
19.2E - DiSEqC 1.0, port B
voltage mode - polarization
fast DiSEqC - no
toneburst - no
tone mode - off
increased voltage - no
 

Attachments

  • 20221123_192007.jpg
    20221123_192007.jpg
    209.1 KB · Views: 34
  • 20221123_192101.jpg
    20221123_192101.jpg
    176.9 KB · Views: 21
I was thinking about what frequencies blindscan will display (GREEN - MANUAL), not services
screenshot_20221123212722.jpgscreenshot_20221123212748.jpg
OpenViX has an excellent feature, transponder verification without real scan (Signal Finder - YELOW Service list)
screenshot_20221123213425.jpgscreenshot_20221123213446.jpg
 
hairybadger said:
I have one input connected, 13E and 19.2E are on it. Both set as Universal LNB.
13E - DiSEqC 1.0, port A
19.2E - DiSEqC 1.0, port B
voltage mode - polarization
fast DiSEqC - no
toneburst - no
tone mode - off
increased voltage - no
Click to expand...
this problem - 22 kHz OFF - still scan with LOF 9750 (Laayoune on 10873V not on 11721V)
1_0_1_1_1_1_CE42AA1_0_0_0_20221124130624.jpg
If you want blinscan to show the correct frequencies, you need to set the extended mode
1_0_1_1_1_1_CE42AA1_0_0_0_20221124132717.jpg
 
Last edited:
defined is used if the user wants to know the correct frequency
 
Setting LOF/L and LOF/H to 09748 enables me to get 13E channels on the correct TPs (RAI 1, for example). I noticed the difference in expected and observed frequency for the higher freq TPs was around 850, so the standard difference between LOF/L 9750 and LOF/H 10600 and tried difference combinations until it worked as expected.

Can't get 19.2E at all now, though :D. Despite all the diseqc/toneburst etc combinations I can try I just can't get it. I could have sworn it was present before. Diseqc B appears to go to 13E, but if I deactivate diseqc entirely I can't get 13E *if* I send another diseqc command.

The multiswitch is a Triax OSP 982, but I can't get any information about it. Note I'm now using OpenPLI - I got fed up with OpenVix crashing.

1718820900492.jpeg
 
Last edited:
Only TAP2 uses SAT1 without DiSEqC, TAP1,3,4 use SAT2 without DiSEqC. Outputs OUT1-9 have a copy of the input signals (you can check if the correct signals are coming from the LNB and they should be properly terminated.
www.yumpu.com

Planungshandbuch

Planungshandbuch Lies mehr über Receiver, Triax, Universal, Quatro, Teilnehmer und Planungshandbuch.
www.yumpu.com www.yumpu.com
www.triax.com

Contact TRIAX here

We kindly ask end-users of TRIAX products to contact the local TRIAX product dealer or point of purchase. Please check out the list of distributors.
www.triax.com www.triax.com
 
Last edited:
EnoSat said:
Only TAP2 uses SAT1 without DiSEqC, TAP1,3,4 use SAT2 without DiSEqC. Outputs OUT1-9 have a copy of the input signals (you can check if the correct signals are coming from the LNB and they should be properly terminated.
www.yumpu.com

Planungshandbuch

Planungshandbuch Lies mehr über Receiver, Triax, Universal, Quatro, Teilnehmer und Planungshandbuch.
www.yumpu.com www.yumpu.com
www.triax.com

Contact TRIAX here

We kindly ask end-users of TRIAX products to contact the local TRIAX product dealer or point of purchase. Please check out the list of distributors.
www.triax.com www.triax.com
Click to expand...
Thanks a lot for this.

OK - the building has 5 floors, 2 flats per floor, 3 staircases, so 15 in total. I'm on the first floor so I guess the taps go to the two flats on my floor and the two below. I have no way of knowing which tap I'm on without disconnecting stuff, though. Unfortunately it's rare that the cupboard is open. I'll need to get the tool to open it... So one of the sats uses no diseqc, and one uses ...? Hmmm.
 
Last edited:
Back
Top