Stream reader settings

[Archive-8]

What settings do I need to change in the streamreader ini file please to work my tbs6925 card properly?

[StreamReader]

Log=1
;Enable log

NoPidFilter=1
; Disable PID filtering

Device_Id=0
; Active device. See log for list available devices

InitTune=1
; Enable initial tuning on start graph. Default disabled.

;LNBPower=0
; Disable LNB power. Default - LNB power enabled.

LNBPwrOff=1
; Power-off LNB on stop. Default - not power-off LNB on stop

;Repeats=0
; SendDiSEqC repeats. Default 2.

; ! EXPERIMENTAL ! Direct hardware control
HWControl=1
VoltBoost=1
;! Voltage boost (+1V)
;FastTune=1
;! Tuner IC autocontrol from demod
;Delay=10
;! RFScan delay after set tuner (in ms)
;BBGain=8
;! Tuner base-band gain
;RFScan=0
;! RFScan mode. 0 - raw AGC integrator values, 1 - dB (default)
;RFLevel=2
;! RFLevel type. 0 - dBm(default), 1 - dBmV, 2 - dBµV
;AGCIQBeta=0
;Delay=20
;DSS=1
;TrickAPSK=1
;FrameMode=1
;DemodMode=0
;BLScanStd=1
;BSAlgo=1
;BSPass=2

;! Change IF range (default 950-2150MHz)
IFStart=925
IFStop=2175
LNBMid=6000
LNBStk=20000

BDAType=TBS_NXP
; Preffered BDA device type (extension)
; WIN7 - Microsoft Windows 7 BDA extension
; TT - Technotrend BDA API
; TH - Twinhan(Azurewave) BDA extension
; TV - TeVii BDA API
; TBS - Turbosight BDA extension (CX2388x based)
; QBOX - Turbosight-QBOX BDA extension (Cypress FX2 based)
; TBS_NXP - Turbosight-NXP BDA extension (SAA7160 based)
; DW - DvbWorld BDA extension
; CXT - Conexant BDA extension
; GNT - Geniatech BDA extension
; HAUP - Hauppauge BDA extension
; OMC - Omicom BDA extension
; BST - Bestunar BDA extension
; CMP - Compro BDA extension
; ANYSEE - Anysee BDA extension
; GNP - Genpix BDA extension (3dparty driver)
; GNPADV - Genpix BDA extension

;Modulation=2
;Default modulation for SetChannel. Default - Autodetect
; 1, QPSK, DVB-S, S
; 2, 8PSK, DVB-S2, S2
; 3, 16APSK
; 4, 32APSK
; 5, QPSK2, QPSK-S2
; 6, QPSK-T, QPSK_T
; 7, 8PSK-T, 8PSK_T
; 8, 16PSK-T, 16PSK_T
; 9, DirecTV, DSS

;Fec=2
;Default FEC for SetChannel. Default - Autodetect
; 1 - 1/2
; 2 - 2/3
; 3 - 3/4
; 4 - 4/5
; 5 - 5/6
; 6 - 6/7
; 7 - 7/8
; 8 - 8/9
; 9 - 9/10
; 10 - 1/4
; 11 - 1/3
; 12 - 2/5
; 13 - 3/5

;Inversion=2
; Default spectral inversion for SetChannel. Default - Autodetect
; OFF or NORMAL or 1
; ON or INVERTED or 2

;Pilot=2
; Default S2-pilot for SetChannel. Default - Autodetect
; OFF or 1
; ON or 2

;RollOff=25
; Default S2-rolloff for SetChannel. Default - Autodetect
; 20 or 1 - 0.20
; 25 or 2 - 0.25
; 35 or 3 - 0.35

 

[CrazyCat]

all ok

 

[Archive-8]

As I am trying to scan Ka band, and it is only picking up 1 of the 4 signals I normally get.

Thanks for your reply.

 

[CrazyCat]

what lnb params ?

 

[Archive-8]

It's an invero White Ka lnb L+R,
L.O. 21200

19.7 to 20.2

 

[CrazyCat]

So your lnb params in coinfig is ok.
LOF > LNBStk - so IFFreq = LOF - Freq.