Technomate TM-1500CI+ firmware update?

Messages
5
Likes
0
My Satellite Setup
d
My Location
belgium
#1
Hi all,

I have a Technomate with firmware version 1.53... how can I update this and where can I find the software to do so. www.technomate.Com only has the 1.53 version.... You can post here or send by mail to
No e-mail addresses use the forum.
READ FORUM RULES, thank you.

Thanks.

Marc
 
Messages
27
Likes
0
My Satellite Setup
A cheap 'n' nasty Silvercrest and an old (but good) TM1000D. 28, 19, 16 and 30W
My Location
Scottish Borders
#2
Head for the Links Section on this very forum and you will find plenty of links to other sites offering firmwares. Just a question of picking one you like the look of, there is only one alternative firmware to the official one, I think.
 

rolfw

Believe it when I see it Admin.
Staff member
Messages
37,698
Likes
1,286
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
#3
Messages
5
Likes
0
My Satellite Setup
d
My Location
belgium
#4
Checked the pages but none of them apply to my model, so any help still requested. Thanks.
 

rolfw

Believe it when I see it Admin.
Staff member
Messages
37,698
Likes
1,286
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
#5
Messages
5
Likes
0
My Satellite Setup
d
My Location
belgium
#6
Thanks guys, the altsat forum resolved the problem. Listen one more question regarding the receiver. I have 2 slots, one where you slide in your card and one that looks like a pcmcia. The pcmcia slot always gives me coded channel, however if I use that card in the upper slot it works fine...any solutions to that? Thanks in advance.
 

rolfw

Believe it when I see it Admin.
Staff member
Messages
37,698
Likes
1,286
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
#7
The CI slot is for an additional CAM, so if you had two viewing cards, you could put a Nagravision/Conax/Mediaguard/irdeto CAM in there with a subscription card. :)
 
Messages
5
Likes
0
My Satellite Setup
d
My Location
belgium
#8
I knew that was for an additional card and I do have two...but do you have to install the CI thing? Since both cards work in the normal slot but the CI doesn't seem to work... always says coded signal...
 

rolfw

Believe it when I see it Admin.
Staff member
Messages
37,698
Likes
1,286
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
#9
The CI slot requires a CAM, do you have one in there?
 
Messages
5
Likes
0
My Satellite Setup
d
My Location
belgium
#10
Yes I do, an official mediaguard CAM...and the weird thing is that if I remove the smartcard that's in there and just plug it in, then there is no problem, however if I put it in via the mediaguard cam it says that the channel is codeD...something weird... do you need to install it or something or change a code somewhere?
 

rolfw

Believe it when I see it Admin.
Staff member
Messages
37,698
Likes
1,286
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
#11
Silly question, but have you tried the card both ways up?
 
Messages
2
Likes
0
My Satellite Setup
Technomate 1500CI+super
My Location
N.Ireland
#12
If you use a CAM in TM1500CI, try to reset patching: go to menu-system information- and press 2004 with remote
 
Top