A
Channel Master/Laminas 1.8m project
- Thread starter Captain Jack
- Start date
timo_w2s
Retired Mod
- Joined
- Sep 28, 2005
- Messages
- 4,359
- Reaction score
- 2,883
- Points
- 113
- Website
- www.timo.me.uk
- My Satellite Setup
- See Signature
- My Location
- Maidenhead, UK & Helsinki, Finland
This thread is making me want to get my 1.2m CM dish for 1W in the ground. I think that could be next week's project if the weather is OK.
A
Archive4
Guest
I´ll try to make this the last ( and on this occasion slightly tenuous link, musically ) but promise nothing on account of my schizophrenic tendency, on what is, after all, a very serious post about dish installation.
- Joined
- Jan 1, 2000
- Messages
- 35,625
- Reaction score
- 8,586
- Points
- 113
- Age
- 59
- Website
- www.sat-elite.uk
- My Satellite Setup
- A little less analogue, and a lot more crap.
- My Location
- UK
Any other person would've made a profit)
Captain Jack
Burnt out human
- Joined
- Oct 21, 2006
- Messages
- 11,811
- Reaction score
- 7,994
- Points
- 113
- My Satellite Setup
- See signature
- My Location
- North Somerset
More work done on the Jumbo motor this morning. As the motor's spindle at the bottom has a groove - something that does not exist on the original one - to stop the bottom plate rotating around if the bolt isn't done up tight, I thought I would adapt the original bottom plate to make use of it.
I've also replaced all the bolts to INOX/stainless steel/нержавейка including the top declination adjusting screw. It's all done up tight, since the declination will be handled by a jack rather than be fixed.
Have also done the trunking along the garden fence but missing a few bits for handling the corners - so need to order those.
Also ordered more steelwork to do the declination and actual attachment to the dish. Really need to get that welder....
I've also replaced all the bolts to INOX/stainless steel/нержавейка including the top declination adjusting screw. It's all done up tight, since the declination will be handled by a jack rather than be fixed.
Have also done the trunking along the garden fence but missing a few bits for handling the corners - so need to order those.
Also ordered more steelwork to do the declination and actual attachment to the dish. Really need to get that welder....
timo_w2s
Retired Mod
- Joined
- Sep 28, 2005
- Messages
- 4,359
- Reaction score
- 2,883
- Points
- 113
- Website
- www.timo.me.uk
- My Satellite Setup
- See Signature
- My Location
- Maidenhead, UK & Helsinki, Finland
What kind of trunking are you using? I need to sort something out too as my dish will be half way down the garden.
moonbase
Small Dish Man
- Joined
- Mar 29, 2004
- Messages
- 4,377
- Reaction score
- 4,481
- Points
- 113
- My Satellite Setup
- .
- My Location
- UK
CJ,
The swing bolt used for the declination looks good, could you please let me know the supplier?
Thx
- Joined
- Jan 7, 2009
- Messages
- 5,606
- Reaction score
- 6,083
- Points
- 113
- Age
- 58
- My Satellite Setup
- Some SAT-related hardware.
- My Location
- N-E from Riga
Nerūsējošais tērauds, I like it!
Good job!This is something must at household.
A
Archive4
Guest
Captain Jack
Burnt out human
- Joined
- Oct 21, 2006
- Messages
- 11,811
- Reaction score
- 7,994
- Points
- 113
- My Satellite Setup
- See signature
- My Location
- North Somerset
I'll take it!
Captain Jack
Burnt out human
- Joined
- Oct 21, 2006
- Messages
- 11,811
- Reaction score
- 7,994
- Points
- 113
- My Satellite Setup
- See signature
- My Location
- North Somerset
Timo, I am using 25mm trunking that you can get from DIY stores. It comes with assorted joiners and terminators (yes, Brian, of the Schwarzenegger
). I got a 20 pack from Screwfix...Tower Conduit Heavy Gauge 25mm x 2m Black (40m) Pack of 20
Here's what it looks like - not the best pictures and it's not finished yet. I managed to fit 3x coax cables and 2x 36v motor cables with room for another coax. A 20mm one is also available and is probably better for your needs.
I am using these along with a joiner like this.
A
Archive4
Guest
Spoilsport!It comes with assorted joiners and terminators (yes, Brian, of the Schwarzenegger
Oh what the hell, I went and found it anyway, so I´ll post it!
Last edited by a moderator:
- Joined
- Jun 28, 2003
- Messages
- 18,025
- Reaction score
- 4,046
- Points
- 113
- My Satellite Setup
- -----------See sig-----------
- My Location
- Wirral, NW UK and Vaucluse, France.
Quitter!
This the concrete base for the garden shed, sorry workshop, going down in 2009. All mixed by us using the concrete mixer shown. The colour scheme is my brother's idea...
- Joined
- Jun 28, 2003
- Messages
- 18,025
- Reaction score
- 4,046
- Points
- 113
- My Satellite Setup
- -----------See sig-----------
- My Location
- Wirral, NW UK and Vaucluse, France.
It explodes on contact with testosterone I believe.
A
Archive4
Guest
- Joined
- Jun 28, 2003
- Messages
- 18,025
- Reaction score
- 4,046
- Points
- 113
- My Satellite Setup
- -----------See sig-----------
- My Location
- Wirral, NW UK and Vaucluse, France.
You want more pics?
Captain Jack
Burnt out human
- Joined
- Oct 21, 2006
- Messages
- 11,811
- Reaction score
- 7,994
- Points
- 113
- My Satellite Setup
- See signature
- My Location
- North Somerset
Made a start on the motorised mount for the dish. Very simple - just two iron angle pieces, a couple of threaded rods and two rose joints. The rose joints will bolt onto similar 'rails' on the Jumbo motor and will form the hinge for the dish to move on. The end of the jack will attach to the 12mm rod at the top. I may adjust the attachment mechanisms but this is the general idea and will be more or less the same as the one I had for my Gibertini dish.
(the rod at the top is for illustration - it will be one piece on the end product)
(the rod at the top is for illustration - it will be one piece on the end product)