kaon sat upgrade

[ce2de2]

hi,
have updated my xtreme ucas with DSC-911UZ_UCAS-HW13.42.65 files.
working with tps.
but can't seem to clear nagra 6fo1 or 6e01. abs-cbn on hotbird using the emu.
can anyone help? thanks

 

[Hosam29]

Hi,I dont know why i cant oppgrade my reciver.I get this message:

[ Upgrade mode. ]

File open O.K.!
> New version binary.
-. Target loader version :L 618
-----------> Front :: 74HC164 used (connector: 14pin)
-----------> Target 2M Flash.
-----------> Target SST FLASH-2M.
Connect Success
//==================================================
// Target: L 618, u-C[0] , FLS[2M], KSC-511Z, H/W(12.01.A5), S/W(02.00.00)
//==================================================
Target Model Mismatch : KSC-511Z
Upgrade Fail
STB normal start.
[ Upgrade mode. ]

File open O.K.!
> New version binary.
COM4 Off !!! ("Enter" key to reconnect.)

 

[lokesh]

Hello there
I have a kaon receiver provided by my service provider Dishtv in India to watch its channels which r broadcast using conax from nss6 @95 east
its details are as follows
Loader Version: - 2.1.6



SYSTEM RESOURCES:-

Flash Memory: - 1 Mbyte

SDRAM: - 8Mbytes

Main CPU MPEG Chip: - STi5518



TUNER

Frequency range: - 950MHZ-2150MHZ

Symbol Rate: - 2-45Mbaud

Demodulation: - QPSK

Input Connector: - F type female (75 ohm)

Fec Mode Rate: - ½, 2/3, 3/4, 5/6, 7/8.


its hardware version is 01.00
and s/w is 01.05( I think that original software has been modified for the company use)
receiver model is KSC 100 MCO

please help me by providing update for this receiver with loader.
Suppose I updated the receiver with another software, than will its original serial number and U/A number will also be modified? If this is the case then I won't be able to receive its original subscription.
please suggest

 

[lokesh]

ALL ABOUT KAON RECEIVER​

Friends, I required some genuine help from all of you. I have put up my receiver into serious trouble. I have a KAON receiver from www.kaonmedia.net I have purchased this receiver to use legal service from DISHTV INDIA (www.dishtvindia.com). Although the receiver make and model is similar to ‘KAON KSF 100 CO’ but its hardware and software version have been modified and it shows the following version.

Loader version: - 2.1.6

H/w: - 01.00

S/w: - 01.05.00

Model name: - KSC-100 MCO. (The model name I think probably have been changed)



Actually I have crashed the receiver software. I tried to reload the software but didn’t find any matching software. Lastly I got angry and updated my receiver with KSC-511Z

H/w: - 12.05.A5

Using the loader called KUP230 in engineering mode. Finally my receiver started. Everything is working fine except one great problem. I AM NOT GETTING ANY SIGNAL. One important thing I noted is that, I can see a flashing logo of ‘CROSSED DISH ANTENNA’ on left top of my TV screen.



Another important thing is that I might have damaged my receiver’s serial number and U/A number during all this up gradation. Without this I cannot watch my legal subscription.



Now I have opened up my receiver and carefully noted each and every hardware to get help from all you friends. I am providing all these details below.



Loader Version: - 2.1.6

H/w: - 01.00

S/w: - 01.05.00

Model name: - KSC-100 MCO



SYSTEM RESOURCES:-

Flash Memory: - 2 Mbyte

SDRAM: - 16Mbytes

Main CPU MPEG Chip: - STi5518



TUNER

SHARP

Frequency range: - 950MHZ-2150MHZ

Symbol Rate: - 2-45Mbaud

Demodulation: - QPSK

Input Connector: - F type female (75 ohm)

Fec Mode Rate: - ½, 2/3, 3/4, 5/6, 7/8.



OTHER

Integrated CONAX + one blank CI Module.

Memory: - 39VF 1602 (from SST)



After up gradation to KSC 511Z

H/w: - 12.01.A5

S/w: - 02.00.00

Ca: - 2.2.2



Friends, please help me to get out of this situation. The service is not accepting the receiver due to self alteration and demanding very much. So, please tell me which software will work with my model and how can I get Serial number and U/A number of my receiver back.

Please provide a genuine help. I will also send the same text to KAONMEDIA help desk.

Hoping for a positive reply soon.

Good day..

 

[patelkaushikp]

Hi Lokesh

Please Chek It Lnb Voltage { 14v-18v}

This Product Provider Is Asian Electronics & Chang In The Bord
Like This Voltag Stage

Please Try It
Good Luck

 

[reza-n]

hi friends
somebody send me the last version of hornet baby upgrade software.
Thanks A lot.
reza

 

[fefa]

please help me about s/w for kaon k220 to find
thanks a lot

 

[harifoz]

Does anyone will help me to upgrade Kaon KSF-200?
which s/w I have to go.

thanks

 

[mouradest]

Hi
I want to upgrade my KAON 200m satellite receiver to open mediaguard/viaccess & ....
I have serial cable, PC, and kaon firmware and software's but I do not have favarite result.
Thanks about your guides

Hi,

Are thre any new software for kaon receiver 200 to open polsat and tps channel...

Thanks and success to all.....

 

[Turok]

Hello!
after uprading,my xtreme hornet,the menu password,has been resetet ksc 570 with build in skycrypt!
now,its inposible,to enter the installation menu...
123456 does not work,can anyone,tell me,what i must do,to make,a factory reset,that i come back to default settings?
or is there any masterpw,that i can try?
thx for help!

 

[andysly]

try 0000
or 1212

 

[Turok]

Hello!
after,upgrading the frimeware,i have 5 Digits to Enter,not 4,thats the strange thing,any ideas?

 

[joe9001]

Someone there can help me i have a big problem i installed some wrong flash now my reciver shows 8.8.8. and i can't reset, what i do?
Help please i very need it

 

[Turok]

Hello!
welcome on board!
when you destroy the bootloader,and flashing over normal comport does not work,then i jtag interface,is the only way,to restore your receiver,there are also bootloader restore bootloader,or erase the memory,when this also not work you need a jtag interface!
what modell do you have?

 

[markmarios]

hello there, people.....
i need your help, i do have a receiver called koan ke620 and i would like to update it, does anyboddy know which fiiles i have to update and how i can update the receiver, i is the benifit if you update the receiver??

 

[Topper]

Welcome to the forum markmarios

I would not bother it was sold as an FTA receiver and whilst there was patch support in 2006 it would appear there is not any support now unless anyone knows different

 

[tdejan]

Hello,
i have KSF 570, which I was told was 16.C0.A1 :| now after what happened not sure.
I did a firmware upgrade, the download was OK, but now the receiver is dead and shows only an "8" on the front display. This is the output of the KUP 230:
File open O.K.!
> Old version binary.
-. Target loader version :L 219
-----------> Front :: 74HC164 used (connector: 14pin)
-----------> Target 2M Flash.
-----------> Target AMD/ST FLASH(TOP).
Connect Success
//==================================================
// FileInfo: AT-7010DZ, H/W(16.C0.A1), S/W(22.00.07)
// Target: L 219, u-C[0] , FLS[2M], KAON TEAM, H/W(FF.00.FF), S/W(03.00.00)
//==================================================
Target Model Mismatch : KAON TEAM
The set-set-box eeprom/flash is blank!
The eeprom data: 0, 8,b9,KAON TEAM , 3, 0, 0,ff, 0,ff
DownLoad Start
DownLoad Success
DownLoad CRC Check OK
Flash Write Start
Flash CRC Check OK
Upgrade End

What should I do? Any suggestions? Please help.

 

[Topper]

What should I do? Any suggestions? Please help.

1. Jtag it, assuming you can find the Jtag file and the mother board has jtag connections
2. Bin it

 

[Turok]

i have ksc 570 here!
that is no longer in use!
,with build in skyrypt,when you cant reaktivate your stb ,youcan have my ksc 570 if you want!

 

[tdejan]

Hi guys,
I have tried to install Kaon Classicos 1.94 firmware on Kaon KSF 570 12.01.05 Boot loader 2.1.9 v4. After the transfer with KUP the receivers freezes and "halt" is shown on the display.
Any ideas?