No I think the picture and sound quality is ok. But the problem is with booting. when I changed the receiver software with that of kaon 511z firmware then it booted rapidly. All this hapenning due to Dishtv software modification according to there use. let's complain this to dishtv.
I have a few question
1) how can I update software by set-to-set method?
2) how can I take a backup of my receiver using my pc.
any way here r some of the information which my pc received from Kaon ksc100 receiver by dishtv using Hyper terminal.Please have a look and give comments.
AVMEM SIZE = = = = 100000
STAVMEM_Init()=OK
STAVMEM_CreatePartition()=OK
STEVT_Init()=OK
STPWM_Init()=OK
STCLKRV_Init(CLKRV0)=OK
STI2C_Init(back)=Ok
STI2C_Init(front)=Ok
DECN_Init()=OK
VTG_Init()=OK
STVID_Init(VID0)=driver changed at 3 April 2003=Ok
OSD_Initialize=(OK)
==============================================
Version 2.1.6 v1
Date Apr 01 2005, Time 23:04:21
NO MICOM : [EuroLoader - Sat384] 1/2M !
==============================================
[FE] Version : 02.03.00 Last Update : 2004.06.16
================> HW_Ver = 0x12C501 : 0x0D, 0x2A, 0x4A <=================
DVB TYPE = 0x1 !!!!
BOARD TYPE = 3 !!!!
CI STATUS = 1 !!!!
VIDEO INVERTED !!!!
gIS_LEDFront = 2
___C_1 Detected !!! gIS_LEDFront= 2, gHEAD.mcVideoInvert = 1
HWC_VideoInvert(1)
[0], CH_ADDR[0xc0182cc4], CH_IDX[15], TUN_ADDR[0xc0082c90], TUN_IDX[0]
BOOTLOADER :: TS SERIAL = 0
[REREADCLOCK] 0-0-0, 0: 0. 0
FLASH ID: 0x234a, COM ID: 0x00bf
sdVerifyMasterOrSlaveThroughPC() = 1
NO_ACKNOWLEDGE with PC.
___ V300 BOARD DETECTED !!!!
Hdl->mcChanType = [0x0c]
Hdl->mcTuneType = [0x89]
[0x00] SHARP 0614 Is detected !!!
Hdl->mcChanType = [0x0c]
Hdl->mcTuneType = [0x89]
FE_GetTunerName(0) = ZL10
FE_GetTunerName(1) = ZL10
HW OUI:0008b9 mdl=0x2802 ver=0x0100 msk=0x0000
SW OUI:0008b9 mdl=0x2802 v
*jumpCode = 0xffffffff
gFLASH_BASE = 0x7fe00000
Jump : 0x7feffffe
STAVMEM_Init()=OK
STAVMEM_CreatePartition()=OK
STEVT_Init()=OK
STPWM_Init()=OK
STCLKRV_Init(CLKRV0)=OK
STI2C_Init(back)=Ok
STI2C_Init(front)=Ok
STCLKRV_Open(CLKRV0)=OK
STAUD_Init(AUD0)=Ok
STDENC_Init(DENC0, InvOut 0)=OK
STVTG_Init(VTG0)=Ok
STVID_Init(VID0)=Ok
OSD_Initialize(OK)
[FE] Version : 02.03.00 Last Updat6
SetPort4 = 0::________GPIO_ReadPort4 = 0x1f
SetPort4 = 1::________GPIO_ReadPort4 = 0xff
THIS IS LOCOST NORMAL FRONT !!!
___C_1 Detected !!![0], CH_ADDR[0xc009a31c], CH_IDX[15], TUN_ADDR[0x7fe11c64], T
UN_IDX[0]
[REREADCLOCK] 2002-1-1, 0: 3.13
size : 148
NO SCART..
NO SPDIF..
=============================================
VERSION : 2.7.5 (2005.03.25)
MODEL : KSC-100MCO (BUYER CODE : 40)
DATE : Apr 15 2005
TIME : 17:10:31
=============================================
FLASH = 0x234a
[MC] Version : 02.02.03 Last Update : 2003.10.21
[TTXOSD] Version:02.01.09, Last Update:05.03.04
[PSI] Version:3.0.0, Last Update:05.01.14
[DB] 4000CH, 8FAV, EPG_WEEK:ON, NEW_COLOCK:OFF, GUI_T:OFF, __K4_OPTION__:OFF, (1
92512,3570)
[CONAX] Version:3.1.3, Last Update:05.02.04
####### CI DETECT #######
[CI] Version : 02.02.02 Last Update : 2004.02.02
Hdl->mcChanType = [0x0c]
Hdl->mcTuneType = [0x89]
Hdl->mcChanType = [0x0c]
Hdl->mcTuneType = [0x89]
FE_GetTunerName(0) = ZL10
FE_GetTunerName(1) = ZL10
[CONAX] Initialize complete
MMI_TYPE :: MMI_K15
MMI_API_VERSION :: 5.2.0
MMI_FLASH_VERSION :: 1.0.0
MMI_E2PROM_VERSION :: 1.0.1
MMI START OK : fa0
Statusbar2 : Reading the Smartcard